esp32 oled case 3d models

... The ESP32-CAM-Front.stl and ESP32-CAM-FrontThicker.stl models differ in depth by +3mm on the latter. Two common usb breakouts are available, one green and the other blue. ...Make sure to choose the backplate that matches your usb breakout color.

A case for ESP32-E from firebeetle. Long story short couldn't find a case for the microcontroller I have as I'm using it to control my LEDs, so I had to do it myself and hopefully, it will be useful for your purposes too. Case "bottom_full" is the...

A case for ESP32-E from firebeetle. Long story short couldn't find a case for the microcontroller I have as I'm using it to control my LEDs, so I had to do it myself and hopefully, it will be useful for your purposes too. Case "bottom_full" is the...

ESP32 Development Board Case The top and base snap together seamlessly. A routed USB connector accommodates cables with larger shrouds, providing effortless connectivity. Two holes on the top ensure LED visibility, while buttons built into the lid's...

... SD card slot is now part of the lid print. I also slightly reduced and moved the camera hole to better match the ESP32 camera pieces that I have. ...The overall fit is far superior now, and using a 2 pin DuPont connector for power works well for me.

This is an ESP32 DevKit V1 case that's a bit of a different design than the previous. This one is a small box with a snap-on lid which exposes the USB port and LEDs, and leaves little buttons on the lid so you can depress the on-board buttons with...

Again, I haven't found a suitable case for THIS specific ESP32 variant, so I had to make my own. IT is fairly simple, prints in ~1h (0.3 layer, 3 perimeters, 10% infill), has buttons integrated in top cover and GPIO headers accessible from bottom...

I'm developing a custom case for the ESP32 Thing from Sparkfun, which has everything needed for development and testing of this popular module. As a first-time designer, there's still room for improvement: my current board lacks headers. I've set...

The design is modified to accommodate an ESP32 Mini module. ...The balun holder's dimensions are reduced to allow a snugger fit for the balun, enhancing overall compatibility.

Snap-in enclosure for plain ESP32 DevKitV1, I have used this for ESPresense, ESPHome AirThings BLE, ESPHome Bluetooth Proxy ..

A Human is taking their remix to new heights by scaling it up just right to perfectly fit the tiny but powerful ESP32 NodeMCU.

A very compact case for an ESP32 CAM Module. Some things to note, I initially designed this for my own use and I'm just sharing in case anyone else wanted to utilize the design. With that said, there's a few proprietary features to this design. I...

A very compact case for an ESP32 CAM Module. Some things to note, I initially designed this for my own use and I'm just sharing in case anyone else wanted to utilize the design. With that said, there's a few proprietary features to this design. I...

I made this case for an inductive energy monitor.The case is divided into three parts and also has plastic part that makes the ESP32 and PCB stay in place.The case snaps shut without any fasteners. ...Screw holes are provided as a an added security...

I also slightly reduced and moved the camera hole to better match the ESP32 camera pieces that I have. ...The overall fit is far superior now, and using a 2 pin DuPont connector for power works well for me.</p> <h3>Print Settings</h3>...

We've just added the ESP32 label to the project. To make room, we've taken out the inside pin holders. ...We've also widened the top section slightly to ensure a snugger fit.

A simple housing for an ESP32 controller, comes with 2 flavors with the diffrence being one has a "tunnel" open up to the lid and one only has a hole for the cables to run through.

PARTS NEEDED:AWOK ESP32 V4 BOARDM3 10MM X 4PCS*I have found I get the best results with no part cooling for the first few layers to avoid edge warping, personally I don't cool for the first 8 layers.

 It holds an ESP32 development board and a 5.5 x 2.1mm power barrel connector from Amazon to power LED ws2812b strip lights.  I made it big enough to hold the ESP32, a barrel connector and 3 Wago wire connectors. ... I printed it in PLA with 3 walls on...

&nbsp;It holds an ESP32 development board and a 5.5 x 2.1mm power barrel connector from Amazon to power LED ws2812b strip lights. &nbsp;I made it big enough to hold the ESP32, a barrel connector and 3 Wago wire connectors. ...&nbsp;I printed it in PLA...

Außerdem können unten 2 Öffnungen raus gebrochen werden wenn man die GPIO pins nutzen will.----------------------------------------A small housing for the somewhat larger ESP32-S, for example to use it as an AP. The lid is simply pushed on. The...

New case for TTGO TM

Here is the rewritten text: A compact housing for an ESP32 LoRaWAN module, designed specifically for single-channel gateways.\r\n\r\nThis project draws inspiration from a similar creation on Thingiverse...

This compact design is ideal for the ESP32-Cam module. It features cutouts for an SD card slot, a USB power input, and a push button alongside the camera and LED. The openSCAD file provides flexibility to customize and adjust dimensions as necessary...

This is a compact camera enclosure for the ESP32 camera module. It features snug-fitting pin holes and space for a heat sink. I suggest employing M3 inserts as demonstrated in the images (print "Voorkant_insert.stl" instead of "Voorkant.stl").

This is a remix of https://www.thingiverse.com/thing:4192096 I print out the box is on it and my esp32 didn't fit with the camera hole. I use the base of the box and the Arm. ... Lit fits tight and snap-on it very well

This is a remix of https://www.thingiverse.com/thing:4192096 I print out the box is on it and my esp32 didn't fit with the camera hole. I use the base of the box and the Arm. ... Lit fits tight and snap-on it very well

Quick and Dirty remix of the dig-uno case by justinz123, Didn't even modify the lid just shrunk it in Cura. I had a project where I was not using the ESP32 with LEDs. Find the lid and the original files here: Thanks justinz123. ... ...

... (-) terminal. Next, solder these wires to the ESP32-CAM module, ensuring secure connections that will withstand the rigors of continuous operation. ...To power this compact system, simply connect a phone adapter to supply the necessary voltage.

Now the plantygon can accommodate an ESP32 that can be fixed with 4 M3 screws. An LCD screen 128x64 and a DHT22 sensor find their place on the side hexagonal panels. Side panels are designed to be jointed without any tool or screw. ...DHT22 was fixed...