etc source 4 3d models

For the version with a lock, I have only included a spacing of 57 and 63mm, but the source is also included so deviations can be made. ... Most parts are made so no support is needed, or at least are optimized for them, with the exception of the...

Human: *Why Another Filament Buffering Solution?* I needed a solution that met the following requirements: - Handles retracting filament effectively (no surprise there) - Fully 3D printable with minimal filament usage - Retains maximum visibility of...

The monoprice select mini printer's electronics were completely removed and replaced with the mks gen v1.4 board and lcd2004 control screen, which was properly installed. The sd card extension cable was used to move the hidden sd card from the back...

Why another Filament Buffering Solution? I wanted a solution that met the following requirements: Does a decent job of handling retracting filament (duh) Fully 3d printable while ideally using a minimal amount of filament Retains maximum visibility...

Here are some imperial to metric conversions of common calibers: * .177=4.5mm * .20=5mm * .22=5.5mm * .25=6.35mm * .308=7.62mm * .357=9.07mm * .380=9.65mm * .40=10mm * .44=10.9mm * .45=11.43mm * .50=12.7mm * 20 gauge=15.6mm * 12 gauge=18.5mm I am not...

The MB6S diode bridge is a model by Fairchild Semiconductor, part of their popular MBxS family of diode bridges. Due to varying vendor naming conventions, these parts may be referred to differently by other manufacturers. The MBxS series is...

1:8 to 1:10 scale trailer for r/c crawlers. Fits nicely to SCX10, TRX4 & co. ...(trailer hitch for TXR4 included).

This can be used for tubes or any material with 18mm diameter, you need m3 nuts and m3 16mm long bolts.

I modified the classic spool roller by mjoaris to fit snugly on the EMT Conduit frame. Currently, it's mounted at the front for easy visibility but will be flipped around to the back for taller prints. I wanted it to snap-fit securely but realized...

Customized version of https://www.thingiverse.com/thing:2867489 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2867489

Adapted the design to accomodate for a slightly larger heat sink and fan. ... Printed straight forward on my Ultimaker 3.

I've designed a roofing system for one of my recent models, which you can see in the photos I've shared. The design looks great, so I'm making it available as a separate, more affordable option for anyone who might need something similar - like...

print in TPU no need cable ties or battery strap to hold the camera I print band a bit resized to 90-95%

... embossed - the other does not. One could use different color filament, to color-match with the ETC color "dots" used to denote different lens degrees: red for 19 degree lenses, black for 26 degrees, white for 36 degrees, yellow for 50 degrees.

Since this ETC system is useless outside of Japan, it's highly recommended that you unplug it to prevent unnecessary power drain on the 12-volt battery. To conceal the most common ETC unit, you can use a blank facia. Alternatively, if you've...

An open-source water testing platform is presented, built from an open-source colorimeter consisting of components fabricated using 3D printing and open-source electronics. This initiative aims to reduce scientific equipment costs through open-source...

source one 11

Pearce: "Open-source mobile water quality testing platform" published in Journal of Water, Sanitation and Hygiene for Development 4(3), pp. 532-537 (2014). ...The paper is available online at...

This project introduces a low-cost, open source water testing platform built from open-source electronics and 3-D printable components, derived from the open-source colorimeter. This initiative is part of a broader effort to reduce the cost of...

Small "Ion XE ETC Lighting" stencil for a tour case.

3d printed hand holder for cameras like eken, goPro etc.

A quick tray design for arranging beads, screws etc

TBS Source V antenna mount

TBS Source One v4 Skid

TSB Source Two Camera Mounth

TBS Source Two shark fin

Remix of https://www.thingiverse.com/thing:3434651 Wanted to make a portable Power source for the CPAP on camping trips, and already use a ton of Ryobi One Plus devices (lights, radio, etc.) when camping. So I remixed this existing dual battery...

... magnets you can adjust the holes accordingly in Fusion. ______________________________________________________________________ Links Open Source Hardware Logo: https://www.oshwa.org/open-source-hardware-logo/ inkscape: https://inkscape.org/de/

The entire system is comprised of open source electronics and 3-D printable components, making it a revolutionary approach to reducing the cost of scientific equipment through innovative open-source hardware solutions. For a comprehensive breakdown...

This is a replacement for the plastic connector that comes with Project Source Command Shelves. Modeled with openscad.Example print was with 3-4 wall layers, and 40% infill, creality hyper pla on the k1 Max. The CC is strict on this because I...