ethernet cable wall holder 3d models
576806 3d models found related to ethernet cable wall holder.thingiverse
Remixed with smaller dimensions, no clip and a hole to save resources Update: Available a new version with larger dimensions
thingiverse
I found myself in need of a way to organize ethernet cables within the rough width of a wall-mounted rack. I wanted the holder to be able to be chained for as many as needed to make things aesthetically pleasing so I came up with this. ...3 of these...
thingiverse
Customized version of https://www.thingiverse.com/thing:864851 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=864851
thingiverse
This is wall mount for FTP/UTP ethernet cables. 3 mounts are for ethernet cable + power cable. I'm using it for signal and power for IP camera. Printed using new great filament PA 12 (nylon) by https://devildesign.com . It's incredible material...
thingiverse
Ethernet cable wall mount For two sided duck tape or small nails. Moved my son's PC to opposite and had to get cable here. ...Designed during 10 minutes, printed in 30 mins, just in time when we need it ;-)
thingiverse
Ethernet cable wall mount For two sided duck tape or small nails. Moved my son's PC to opposite and had to get cable here. ... Designed during 10 minutes, printed in 30 mins, just in time when we need it ;-)
myminifactory
This is a cable clip designed to be stapled, nailed or screwed to a wall. The provided STL is for 6mm diameter cables (most ethernet cables will fit). Design is parametric, you can alter it in Fusion360 for larger or smaller cables.
prusaprinters
Ethernet cable wall mount For two sided duck tape or small nails. Moved my son's PC to opposite and had to get cable here. ...Designed during 10 minutes, printed in 30 mins, just in time when we need it ;-)</p> Category: Organization
thingiverse
An ethernet cable holder to fix and organize network cabels on walls. When you printed the thing holder, you can screw them with a 4 mm Spax in. ...And then take a cable tie and fix your cable on the holder
cults3d
... file for 5 Cables contains space to put a thin power cable for the same modem. They are put in with nails with a diameter less than 5 mm. Size: 1 cable holder: 7 x 10 x 20.5 mm 3-wire holder: 7 x 10 x 46.5 mm Holder for 5 cables: 7 x 10 x 67.5 mm
thingiverse
This was made for a 5mm diameter ethernet cable, accepts up to 6mm cables. use a 1 to 2 mm diameter nail. ...
thingiverse
Hi, my name is Oleksii I hope you will enjoy my own designed holder for the ethernet cable, which diameter is 5.02 cm. I wasn't printing with supports, but if you are printing this with ABS, I will definitely advise you to add them. -This thing...
thingiverse
This is a simple wall mounted cable support for slim ethernet cables, the inside diameter is 4mm that's optimal for hanging a cable using a dab of hot glue on the base. ...The cable I used is this one:...
thingiverse
Recently ran some flat CAT6 ethernet cables and wanted a clean way to bring them through the wall with to have a direct connection. Made these plates to fit the standard single gang wall box. The holes is large enough to fit the connector through.
thingiverse
https://www.thingiverse.com/thing:1320948 Made 25 % bigger than originals to accommodate Cat 6 Cables. If you are using you will probably need to make 25% bigger again. Added holes for wall mounting. ... Shameless Self Plug: Check out my other...
thingiverse
Holder for ethernet cable CAT6 (diameter +/- 6,4mm) Use VelcroStrap for attachment.
thingiverse
I printed many of these and used them to hold a flat cable to an ethernet cable temporarily and it is working great. ... I made it a tight fit around the ethernet cable so it may damage the cable if you put it on and off multiple times.
thingiverse
A simple wall mount clip for ethernet cables with 5mm diameter. I use it with an Ethernet/RJ45 cable. If your cable is a bit different you can resize it easily. Made for use with double-sided tape. ... Dimensions: 20 x 15 x 6.5mm
thingiverse
Ethernet cable clips and cover for routing along walls. Uses standard course drywall, #5 or similar screws. Versions for one through four cables are included. Versions for one through four cables are included, but the thumbnails may not be...
thingiverse
Holder for 12 Ethernet cables that can be mounted on a side of the table. Mount for the Ethernet switch. ...Has to be mounted underneath the desk.
thingiverse
Customized version of http://www.thingiverse.com/thing:1719073 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1719073 Instructions Using the following options: angel = 50 cable = 8 rows = 1 thik = 1.5
thingiverse
Clip for RJ45 ethernet cable. ...STICK the clip down with double-sided tape. Clip sujeta-cables para cable ethernet RJ45. ...Para pegar con cinta de doble cara.
thingiverse
A simple holder for Ethernet Cat 6 cables (5.5 mm diamater). ...Clips on the cable directly - no additional tools needed.
thingiverse
Very simple 5-hole Ethernet cable organizer. ... 5 holes to accommodate WLAN + 4 other cables.
thingiverse
Clip is designed to fit 15mm heating pipe found in the home and carry up to three 6mm ethernet cables.
thingiverse
I made this out of necessity, and I think it turned out very nice.