ethernet clamp 3d models
49812 3d models found related to ethernet clamp.thingiverse
Use a bot of number 17 nails and make yourself inexpensive cable clamps. ... Sized for standard Cat5 and Cat6 ethernet cables.
grabcad
... in order to fit within the port without interfering with the cable. A belt fastened to the top of the clamp would ensure that the two pieces would not come apart while together.Owen MiddletonInstructor: Kathy StevensonMichigan State University
thingiverse
Here's a basic cable clamp for securing a pair of cables to a stud (or whatever you want to screw it in to). The screw hole was intended to fit a drywall screw, but other's should fit fine. I made this for helping-square up ethernet cables run in my...
thingiverse
This is a cable clamp for cleanly squaring-away up to 4 ethernet cable (CAT5/CAT5e/CAT6/CAT6e/CAT6A/CAT7) when installed in your walls. I've made other similar clamps for single or dual cables. This time I gave more clearence for the cable as I...
thingiverse
Customized version of http://www.thingiverse.com/thing:1094138 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1094138
thingiverse
Customized version of http://www.thingiverse.com/thing:1094138 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1094138
thingiverse
Customized version of http://www.thingiverse.com/thing:1094138 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1094138
thingiverse
Quick 3 cable clamp \ tie down for cat 5-6 cables. Handy for CNC's and printers that use network cable for stepper leads. I used on my MPCNC. Typical cable width I used this for was 6 to 6.5mm diameter. The holes to mount fit #8 screws pretty well.
thingiverse
Simple holder for HDMI and Ethernet. Useful for gaming consoles, htpc, Raspberry, etc... ... Simple to modify, this design is for ~16mm desk table
youmagine
Inspired by http://www.thingiverse.com/thing:1701559 Complete new redesign, fully customizable, using less material, easier to clip onto the plug.
thingiverse
This clamping strain relief device is used to hold ethernet cables in position behind a rack, NVR, hub or modem. Specifically for the NVR it is important to put the cables back to the same position when reconnecting and this clamping strain relief...
thingiverse
Customized version of https://www.thingiverse.com/thing:1543201 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1543201
grabcad
Ethernet Coupler based off of the one produced by UGREEN. ...Ethernet to Ethernet.Dimensions: 1.71 in x 0.92 in x 1.00 inAll dimensions are in inches. ...Sorry for any inconveniences!
grabcad
Modification of Phil Maddox's Duet Wifi to add the Ethernet port.Original: Duet Wifi
grabcad
H10/H11 series10/100Mbit/s 16-pin SMD Ethernet Transformer manufactured by PULSE
grabcad
Type: Ethernet male plugDimensions: 0.47in X 0.51in X 1.63inAll dimensions are in inches. ...Sorry for any inconveniences!
thingiverse
This is a custom box designed to house a circuit for modular sensors on our FRC Bot. ...Five female ethernet jacks snap into place.
cults3d
This is a mod to add Ethernet Keystones to the case so you can plug in your Ethernet from your Stepper motors. ... This exact type of keystones that fit here https://www.amazon.com/gp/product/B01FHC1HXO/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1 ...
thingiverse
This is a mod to add Ethernet Keystones to the case so you can plug in your Ethernet from your Stepper motors. ... This exact type of keystones that fit here https://www.amazon.com/gp/product/B01FHC1HXO/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1 ...
thingiverse
This is an ethernet dummy plug to reserve or protect a network port. It is designed to be printed on its side for strength of the clip. I included a plain version and one with a clip protector. Each one has a version with supports and without in...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=202525 Instructions Using the following options: CustomHeight = 0 Height_Of_Power_Plug_Hole = 14 Clearance_Between_Arduino_And_Sidewalls = 1.5 Standoff_Thickness = 1.6 Height_Of_Standoff = 7...