etx 90 ra 3d models

Dovetail plate adapter for classic Meade ETX-90 RA for a German equatorial mount. This will fit the with the stock RA base attached or just the bare telescope tube. I printed with PTEG for strength. Not sure I would recommend PLA for this. ... You...

This will require cutting and re-soldering the wires and drilling a small hole into your plastic ETX base. Print the box on it's side using tree support (in Cura experimental settings) Print the top flat side down (rotate 180 degrees in Cura)...

BEFORE YOU PRINT: 1. Only the ring need support (for the dovetail overhang) See pictures for print orientation. 2. The original Arca-Swiss clamp I remixed from was too small for my canon mount so I had to widen it. Not sure if that is standard.

Made a much stronger Meade ETX RA Lock Lever. This can be printed in PLA and is plenty strong. Print with 10 walls to eliminate as much infill as possible. This is what gives it it's strength. ...

The hobby foam dew shield my wife had made me for my ETX-90 had ripped along the sew line, so I made this dew shield to replace it. I used a single sheet of self adhesive felt on the inside to make it smooth against the OTA as well as help with...

This is a Bahtinov mask for the Meade ETX-90. ...It was designed for the 90mm clear aperture and 1250mm focal length of the ETX-90.

Needed a Dovetail mount for a finder scope on my ETX-90 telescope.

Simple filter ring created for a Meade ETX-90 to hold solar filter material like (4"x4" Solar Filter Sheet for Telescopes, Binoculars and Cameras)...

I recently acquired a ETX-90 with a computer controlled mount. I had some problems withe the DEC clutch slipping and like everyone else broke the knurled nut loose on the clutch peg. This is my take on a repair for this model of mount. I had the...

This is a red dot finder mount for the Meade ETX 90. ...I had one of those red dot finders from a cheap Bresser DS-2130AT and wanted it mounted on my ETX.

I generated a Bahtinov mask to fit my old Meade ETX 90. ... The mask is designed to fit over the end of the OTA, and uses a fairly large Bahtinov factor to reduce the size of the slots and hopefully increase the contrast for easier focusing.

Je vous propose une queue d'aronde universel type vixen pour mettre un chercheur sur votre ETX-90. Il s'agit d'un collier qui se serre tout autour du tube et sur lequel se trouve la queue d'aronde elle-même composée en deux parties. Vous aurez...

Customized version of https://www.thingiverse.com/thing:1012573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1012573

arca swiss camera mount for telescope with 1.25 "eyepiece You need: 1x M6x60 Bolt 1x M6 Nut 2x steel Spring of pens

The original was way too lose and stripped on the bolt head for the RA lock. So I remixed it for a solid fit. It even works using PLA. ... Enjoy!

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

Easy on and off holder for a laser pointer. Inherently aligned with the tube, no set screw adjustments to fiddle with. Simply attach to the telescope using a pair of sewn elastic straps. Laser pointer model is no-name green light tactical model...

A adapter ring to hookup up the Sony A350 camera to the ETX-90 Telecope. New file: adapter ring from Telescope 35mm diameter to 43mm diameter tubes. ...(connects the telescope to other adapters).

A adapter ring to hookup up the Sony A350 camera to the ETX-90 Telecope. New file: adapter ring from Telescope 35mm diameter to 43mm diameter tubes. (connects the telescope to other adapters). ...

Designed to be printed in TPU so it's a snug fit, If you print in anything other than TPU then you should probably scale it up 1-2% It should be flipped over so the embossed side prints face down on the bed. ... There is a little lip around the...

Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

"RA" a DIY 3d Printable Virtual Reality Head mounted display Fov: 120+ deg Weight: 1lb 8oz Cost: $450 Headtracking: yes video showing the FOV range.http://youtu.be/p10V3lca-DY video of RA in Use.http://youtu.be/pujeMSP6dmo

you need to print 2 of the RA_HELMET_MOUNT.stl, the 2nd one should be mirrored There are 2 "Lens Plates" in this design, one for a LEEP optics variant for the 120+ deg fov, and another that uses 50mm lenses, that give you a 90+ deg fov. the choice...

Ra was considered the King of the Egyptian Gods according to Egyptian myth, however, in reality, Ra was Anubis’ chief advisor, and defacto representative in State Affairs. What’s more Anubis is more inclined towards the study of the Unknown than the...

RA is an ancient Egyptian sun god, the supreme deity in the religion of the ancient Egyptians. ...His name means "Sun".

Ra is the ancient Egyptian sun god. ...By the Fifth Dynasty in the 25th & 24th centuries bc, he had become a major god in ancient Egyptian religion, identified primarily with the noon sun.

Ra was the king of the deities and the father of all creation. He was the patron of the sun, heaven, kingship, power, and light. ...He was not only the deity who governed the actions of the sun, he could also be the physical sun itself, as well as the...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_style = surround_text outline_thickness = 3.0 text_thickness = 4.2 lug_width = 6 border_width = 0 bar_width = 5 glyph_coalesce_strategy = bar...