eufy spaceview angled crib mount by 3d models
951823 3d models found related to eufy spaceview angled crib mount by.thingiverse
So I designed a clamp-mount bracket to angle the Spaceview downward by 25° so that it can see into the crib. ... Thanks a lot to a couple of other Thingiverse citizens for supplying some clever ideas — for example, I borrowed the threaded rod,...
thingiverse
45° Wall mount for eufy Spaceview baby monitor. I'm using Tesa Power strips to attach it to the wall. ...That way it can be removed without damaging the paint and I can also use it in holiday homes.
thingiverse
The adapter angles the Eufy Spaceview baby monitor downwards 45 degrees to eliminate blind spot under the wall adapter when installed upright (you can install the wall adapter upside down, but it can drop if it comes off of bracket). Smaller adapter...
thingiverse
A mount for the Eufy SpaceView baby monitor camera. The mount has an arm with a screw clamp allowing the camera to be clamped and mounted to, for example, a nearby shelf or ledge. The mount holds the camera at a 20 degree angle giving a better...
thingiverse
This is an adapter to attach a Eufy Spaceview baby monitor to the [Modular Mounting System](https://www.thingiverse.com/thing:2194278). ...It is necessary to print it upside down (that is with the modular mount pieces facing upwards) using supports.
thingiverse
Bracket for mounting the Eufy Spaceview baby monitor camera on a window handle. Simply slide onto the window handle from below and twist to lock. Should fit at most window handles. ...Hole diameter is 25mm, in which the window handle should fit...
cults3d
Material needed: 1 x 3mm*10mm screw 1 x 3mm hex nut (depends on you printed ground plate) Or just glue it together English: Here you can print a baby monitor holder for the Eufy Spaceview. You can clamp it to the baby bed. The range can be variable...
thingiverse
Eufy Spaceview Baby Monitor Tripod Base, becase the connector that comes with the camera limits options. ...Highly inspired by Shinwachi
thingiverse
... a remix of [RT3DWorkshop](https://www.thingiverse.com/rt3dworkshop/designs)'s [design](https://www.thingiverse.com/thing:4828390). ... I've just added a -25° angle because I'm on the 2nd floor, and changed the slots to fit my very thin hanging strips.
thingiverse
This is a simple mount to attach a Euby babycam to a tripod. You just need to glue a 1/4"-20 nut in the bottom hole. I printed mine with 20mm layer height and PETG. ...Should work with PLA as well.
thingiverse
The shims included are specific if the Eufy angled bracket angles to the right (angled to the left when looking directly at the camera). The models could be mirrored to be utilized for the left as well. Two shims included to angle the camera down...
prusaprinters
I needed a mount for my Eufy Cam2C that provided more angle when mounted from the ceiling. ...(https://us.eufylife.com/collections/battery-camera/products/t88311d1) </p><p>There are 2 stl files since I needed one that was taller to allow the...
thingiverse
This is a wedge-mount for the Eufy doorbell battery. It uses the mounting holes of my old doorbell button, which is a common doorbell button in the Netherlands. The Eufy backplate is fixed with 3x20 mm screws, as the 3x25 screws that came with the...
cults3d
This is a mount for Eufy Cam on the 4040 extrusions on an Ender 3 V2 (though i'm sure it would fit others as well)
thingiverse
Mount is made for an 80mm drainpipe. ...Can be fastened with a tyrap or something else up to 8mm wide. The standard Eufy mount can be connected to the mount with two M4 screws and nuts.
thingiverse
Rather than redesign the whole part, I decided that I would combine the 15º mounting bracket with and additional 25º wedge and get the 40º I wanted. Installation: 1. 2 nuts are recessed into the back of the 3D printed part 2. Attach the 3D...
thingiverse
The angle is around 30 degrees. It works well for me in the sense that the field of view is optimal. ... I printed (2020) that from grey PLA and after 3 years (2023) part holds up well :)
thingiverse
Needed to change my camera from it's place for a special occasion.. ... Due to the camera size, it was tricky so I was inspired by another source and made this with the Eufy screws.. fits perfectly. Printed, with PLA, 0.15 and no support. ...
thingiverse
I use it to mount to my baby crib, and holds the ipad at a 60 degree angle. ... I use a baby monitor app to be able to watch my newborn
thingiverse
My security camera had to hang under the ceiling and that's why I designed this durable angle bracket. Fits perfectly with the included screw bracket for Eufy and Arlo. The lowering to the screw head is 7 mm. ...Wall thickness 1 mm
thingiverse
Needed a mount for the nanit when we were away from home. ...They don't make anything other than a wall and pole mount that I could find. This will slide right over the edge of our crib and still has a decent angle on the bed.
thingiverse
A non-corner bracket to attach the Eufy Spaceview Baby Monitor to the wall.
thingiverse
This is a crib mount for a Nest Cam. I needed something that would be secure to the crib and also hold the camera securely. This mount worked perfectly for me. ...See pictures and images for to see how it mounts and specs with respect to spacing.
thingiverse
I recently became a father and when traveling with a crib it can be really difficult to find a good place to mount the baby camera. Designed this to hold the camera firmly in place and can snap onto the crib itself for an ideal position. Uploaded...
thingiverse
This is a Wyzecam mount that I created for our Nuna playpen. ...The mount can be adjusted to fit any crib. ...I print it with supports on and the camera opening facing down.
thingiverse
This is a mount I created to allow me to place my Owlet camera on the crib safely. ... I used museum putty to reinforce the cameras stability on the mount.