evic vtc dual 3d models
37882 3d models found related to evic vtc dual.thingiverse
Renfort pour cigarette Evic VTC Dual équipée d'un aérotank kanger D 18.5 mm
thingiverse
This is my design of a Case/Bumper for the Joyetech eVic VTC Dual. There is a .STEP file for costumizing. The THIN file have 1mm wall and the "normal" without an addition 2mm wall. ...Have fun.
thingiverse
Slainte! ... I use irish green colour Elastan D100.
thingiverse
Another case for Joyetech eVic VTC Mini.I used fuzzy skin option in cura (settings in photo). ... You can print test ring before case print to check flow/scale.
thingiverse
A simple little stand for the eVic VTC Mini. It fits the mod in a silicon sleeve, with a little extra room to make it easy to insert and remove, but it still won't tip over or fall out if it's bumped. I didn't include a hole for the USB port, since...
thingiverse
... in place. It fits the eVic VTC Mini with a silicon sleeve, with extra room to make inserting and removing easy, as well as a 30ml juice bottle. ...Print Settings Printer: FlashForge Creator Dual Rafts: No Supports: No Resolution: 0.20mm Infill: 10%
thingiverse
This stand holds: eVic VTC Mini in a silicone sleeve (not particularly snug, so that it's easy to insert and remove) 4 tanks (designed for the Uwell Crown and eGo ONE Mega, but probably works with others) 3 18650 batteries 3 30ml juice bottles 4...
thingiverse
Simple cup holder insert that can hold a vtc-mini vape mod and two 30ml 22mm liquid bottles. One version with open bottom and one closed. ...I designed it for the cup holders in a Mitsubishi Colt, but it should also fit other cup holders.
thingiverse
Joyetech eVic-VTC STL update... ...08.05.2016 00:23Uhr
thingiverse
Evic VTC MINI side panel 26650 Pannello per utilizzare batterie 26650 con Evic VTC Mini Chiude già bene ma è opportuno aggiungere magneti per un serraggio migliore Nb Add magnets for tightening best
thingiverse
Docking/Charging station for EVIC VTC mini. (works with mods in silicon case) Use the spacers(0,5 & 1 mm) to set the height of your micro usb cable. ... M3 x 30 countersunk -- 2pcs M3 nut -- 2pcs spacers (optional) Print Settings Printer: ...
thingiverse
U need disassembly your Joyetech Evic VTC (just two screw) and u need use original spring and original push button (fire and up and down). U need 4 4x1 magnets too. 13/02/2016: added fire_long.stl > it's a longest fire button respect original one, if...
cults3d
Having a Zenith sprayer Ø24mm it bothered me that it protrudes from my box evic vtc mini. So I took its design and modified it. First of all, the box is much lighter, Then it is a little wider and has a lug so that the spray does not exceed. This...
thingiverse
This version has yet to be printed (slightly bigger space for the VTC - should make it easier to put it down while driving, bigger diameter of the cup to ensure a tight fit with most cupholder-fixtures), but the proofing-version I did of it, fit my...
thingiverse
This is a stand to hold a VTC EVic Dual with a siaonara, heatsink, and poseidon bubbler
thingiverse
remixed so i could put two 18650's in parallel or a a vtc battery inside. printed on ender 3 .2 layers supports = lines. cura cr10 draft profile. ... added a version with a reccess for the lid.
prusaprinters
<p>Customized version of <a href="https://www.thingiverse.com/thing:427373">http://www.thingiverse.com/thing:427373</a></p> <p>Created with Customizer! ...<a...
thingiverse
Customized version of http://www.thingiverse.com/thing:427373 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=427373 Instructions Using the following options: height...
myminifactory
So I designed a little desk stand for both the Joytech eVic VTC Mini, my 22 mm tanks and the Ohm Tester that I use to make coils. The design incorporates a dropped front so that you can still connect a USB charging cable to the front while it sits in...
thingiverse
base creata per evitare di far cadere batteria e atomizzatore durante la carica
thingiverse
Customized version of https://www.thingiverse.com/thing:2444760 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2444760
thingiverse
Allows you to keep your eVic handy without worrying of knocking it down. ... The holder is a sleeve that attaches to the eVic body while the hanger clips onto the desk.
thingiverse
Box Mod optimized for Evic by Joyetech phaust@bk.ru send an email for personalization or custom Box Mod Covers
thingiverse
This is a very simple stand for the Joyetech eVIC Mini Vaporizer, created with 123D Design. ...Print Settings Printer: Fabrikator Mini alias Tiny Boy ...