extension cord holder 3d models
357587 3d models found related to extension cord holder.thingiverse
Extension Cord Holder may need to be scaled up a bit to fit the size of the cord. ... also my first make so tips would help.
prusaprinters
Držák na zásuvky na stěnuDržák zásuvek na stůlUpevnění prodlužovačkyExtension cord holder
prusaprinters
I created this Extension Cord Holder to fix Extension Cord I used for lamp, charger and other electro devices. ...It consist from two parts which are fixed with 4 screws. </p><p>I printed them on my Prusa MK 2.5S from PLA with layer 0,35.</p>
prusaprinters
Simple and fast printing USB extension cord holder. Done for this model of cable: https://www.amazon.es/gp/product/B071KWG5J6/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 It can be placed in any of the slots for a 30x30 profile. ...Align the nut...
thingiverse
I made this extension cord holder because i couldn´t find one i liked. So 20 minuts later in fusion 360 this is the result. The holes are 6mm and it fits if you use 5mm screw/bolts to mount it. ... No Support needed, but don´t go over .2 in layer...
cults3d
I made this extension cord holder because i couldn´t find one i liked. So 20 minuts later in fusion 360 this is the result. The holes are 6mm and it fits if you use 5mm screw/bolts to mount it. ... No Support needed, but don´t go over .2 in layer...
cults3d
Holder for extension cord (europe plugs) that everyone can screw on table.
thingiverse
A lightweight wall holder for extension cords I made for my ancient kitchen. ... It's very slim, yet strong enough to hold up a 3 or 4 slot extension cord without any issues.
thingiverse
Holder for AC extension cord under your desk - you can use glue os screws to hold it on place. easy to print - minimum supports needed it hold at place most of the EU cords which I found on the market. ... enjoy
thingiverse
This is a holder to be hanged from a radiator to house an extension cord. The inside is 48 mm wide, it could be made 50 because this one is pretty tight for a standard size used in Finland at least. ...Make it as long as you need, the model is 150 mm.
prusaprinters
If you want to bring a extension cord securely on a wall or a cealing, then print these two litle brackets and clamp the cord with it.easy to print, less material usage and no change to the extension cord it self
thingiverse
Designed this to hold the device side of an USB extension cord. The USB plug is 25mm long, 9mm thick and 16.5mm wide. The bend protection is 4mm wide and the cable is 2.6mm wide. Maybe it fits other plugs, too. ... I use this to put my Logitech...
thingiverse
Needed to hang an extension cord on the back of a cart, so I cobbled up this thing. Instructions Took a while to print, and the last bit of the overhang that goes almost flat had a few problems, but...
thingiverse
Created to hold an expension cord to the side of my table while keeping it fully portable. ...This is the second version. The earlier version does not have a rubber band holder, but this is more practical albeit a bit less aesthetic.
thingiverse
Wall hanger for extension cables, to be held on the wall via screews. ...Big enough for 25m cable, see picture.
thingiverse
Didn't want to put any screws into the desk, so I took the idea from his holder to be hanged from an IKEA SMÅSTAD. The inside is 56mm wide with a small lip to sort of clip the block down. ...I mirrored it for the left and right, so I would have to use...
thingiverse
Had an idea for an extension cord holder that doubles as a charging shelf for your phone. ...Also added one with screw holes but I think using 3M tape is enough.
thingiverse
A replacement for the stock extension cord holder on my Snow Joe snowblower. The one the comes with it is far too small for the 12 gauge extension cord I need, and it arrived broken in any case. This one works in a similar fashion but is designed for...
thingiverse
wanted to wall mount an extension cord. ...Purchased a bindmaster extension cord from amazon (B01N6XUCDY). ...for indoor use only.
thingiverse
This holder is design to snap on the Brennenstuhl extension cord/branch at a 45 degree angle behind my mega heavy stainless workbench. It will need to be adapted to your hardware and bench depending on your needs. But it might give you some ideas. ...
thingiverse
A bracket for hanging up a multi-way extension cord from Biltema https://www.biltema.no/bygg/elektro/grenkontakter/grenkontakt-jordet/grenkontakt-med-bryter-2000038281 Art.nr. ...46-3494
thingiverse
The holder is designed to be low profile to not interfere with plugs. Dimension of 41x53mm is supported by default but the part can be scaled to support smaller or bigger sockets. You can scale and print the test piece to find the correct fit...
thingiverse
Just a simple extension cord cable holder mounted on wall. ...Need glue to stick.
thingiverse
Designed for the purpose of supporting a 25ft cable. I'm sure it could support more. ...It was installed inside my workshop for a movable table.
thingiverse
just made the hook a bit thicker as i was afraid the original might snap
prusaprinters
Holder for an extension cable that screws onto the IKEA LACK. ...Designed for https://www.alza.cz/oem-kf-fb-03-d6128122.htm.Extension cord dimensions lenght 53mm, width 39mm, height doesn't matter.
thingiverse
This was a simple file I created to replace the screws needed to wall mount and extension cord. Use it to glue onto walls, or desks that you don't want to have to screw in. ... If you like this design, please consider supporting me with a tip.