external gpu case 3d models

A External Power Supply case for for Fat PS3, to reduce heat build up inside ps3 and make more space for extra cooling inside ps3, case has right measurements for power supply to fit right in with no problem and it comes with 2 small 40 fan's at...

This is an external case/housing for your control electronics so that you can relocate them outside of an enclosure for your printer. I based the dimensions off of my Ender 3 Pro parts, which I know is similar to the base Ender 3, but I can't...

... Rear part is specifically designed to contain FC5025 floppy controller and SY-002-5-12 AC-DC adapter and they hardly could be treated as general case options - that's why I include generic 'rear_base' version (compare to see the difference).

Duet 3 Case made to be mounted onto Aluminum Extrusion. Support 40mm fan, I used a noctua NF-A4x10 (40mmx10mm) Print with Supports if you don't have good bridging, if you do you you're fine, mine(pictured) was done without supports.. SBC...

This is an easy printable one-piece case for the CC2531 Zigbee Sniffer Board with external antenna. Print the case standing without support and slide the USB dongle in from the back. It should stay inside just by friction. ...Let me know, if it's too...

I designed a vertical stand with wings out the side to stabilize it and prevent it from tipping over. It prints quick, looks clean, works perfectly. Print instructionsUnassociated tags: hard drive Category: Computer Summary I didn't want my external...

Extraction fan Make sure fan direction is extracting (pulling air from inside case to outside) Tested with this 80mm fan http://goo.gl/IZiGcw and this 92 mm fan http://goo.gl/EzRbzx Note that the 80mm fan running full speed at 40 dB is likely too...

Prop up an external hard drive or solid state drive right under your desk.

I built an External Mainboard case for my Ender 3, attaching it to the back of my enclosure. Was this Thing useful? I would really appreciate a cup of coffee donation so I can keep creating useful things late into the night. ... <form...

While the original case is intended as a standalone unit, this remix is intended to be mounted on top of an enclosure such as a Lack enclosure, with all the wires running down through holes in the surface below (I used a single 1.25" hole lined with...

A remix of the AM8 case (https://www.thingiverse.com/thing:2510441) that originated from a remix of the original (https://www.thingiverse.com/thing:2199806), which provided parts for its external casing. Adapted for printing with A8 stock (21.5cm...

Duet 3 Case made to be mounted onto Aluminum Extrusion. Support 40mm fan, I used a noctua NF-A4x10 (40mmx10mm) Print with Supports if you don't have good bridging, if you do you you're fine, mine(pictured) was done without supports.. SBC Mounts with...

Switch on the device, upload the tracker firmware, check the serial output logs to make sure that the sensor works properly- insert and tighten the M2.5 screw to mount the power switcher- insert and tighten the M3 screws on the sensor case- position...

I'm particularly fond of the straightforwardness of this scenario, which prompted me to reimagine it entirely and create an opening for the external antenna. ...In addition, I modified the camera slot to a square shape to enhance its compatibility.

The primary PCB of my Huxley suffered damage, leading to the hot end ceasing functionality. ...Subsequently, an external PCB has been employed to operate the hot end; it securely attaches to a 6mm threaded rod. ...Have fun!

Basic case for the Ender 3 V2 mainboard should have more than enough room for cables.

I have external repeater than translates FrSky 2.4GHz receiver signal into CrossFire TX. RX should be on ~1m wire to not get interfered with TX. This model is a box for RX to keep safe and dry. ... Glue the top plate to the box after receiver is...

Made this hard drive case to compliment my Orange Pi 3 LTS case. The cable I use with this is a Startech SATA to USB 3.0 adapter. While not a rugged case. ...It's more or less designed to add a little bit of protection while this Pi and HDD live in my...

I adapted it to my Seagate SATA-to-USB-Adapter, which allows easily to connect various SATA HDDs as external USB drives. Additionally I changed the PS5 logo to an apple logo, but also attached a version without any logo. ... If you wish another logo,...

... a weight reduction to 50% or less is unlikely. To view additional images of this design, please refer to the provided media links. The battery case is specifically designed for use with the DBpower drone, also known as the UDI Discovery 818a.

Pi2 Case. Used to install custom electronics board. ...Print Settings Printer: Pause I3 Rafts: No Supports: No Infill: 100% solid Notes: Printed with high-quality PLA.

When building the case, consider where to place the USB cable; a hole can be drilled at the side of the top cover, or a longer cable can be used and placed with other cables at the back of the case. Use the FreeCAD file to extract individual parts...

You need to make sure the screws are not too long (6-8mm thread length should work fine) as otherwise they will touch in the cubes used for fixing the sides of the case. I used some hot glue to fix the nuts in the cubes to make sure they dont fall...

External Antenna mounts for fritzbox 7590 AXMay fit other variants. let me know.!!! Involves cutting holes in the air vents !!!The square one fits the vents in the backside. I put mine over the usb port. Cut the vents with cable cutters or nail...

I added a 120mm fan to the bottom of an external control box, threw in a 120mm fan grill, and some support pieces under the motherboard mounting points. I'm not sure if these supports are actually doing anything or not. It's not perfect - I noticed...

It appears that this text is a guide for assembling and customizing a 3D printer case, specifically designed for the BIGTREETECH SKR V1.3 motherboard. Here are some of the key points: **Assembly** * The case has multiple components that need to be...

The case has the following features: Flip-up lid with integrated magnetic closure, sized for these 1" x 1/4" x 1/16" magnets Mounting Location for 40mm fan, roughly centered over X/Y/Z stepper drivers 3 cable bundle tie-downs for XYZ steppers,...

You need to make sure the screws are not too long (6-8mm thread length should work fine) as otherwise they will touch in the cubes used for fixing the sides of the case. I used some hot glue to fix the nuts in the cubes to make sure they dont fall...

The Shelly H&T twists into the lid like in the original case As the Shelly H&T only is rated for 3V you should use some type of voltage regulator! ... additionaly needed: <ul> <li>4 2.9mm x 9mm screws for the lid</li> <li>2 2.9mm x 6mm screws for...

This case is for use with 4x6cm pcb and esp32 with ipex connector on it. The lid has an mounting point for a bme280 board with two screw holes and 6 pins. You need two small round head self tapping screws (m2x5-6mm max) for it. One IPEX to RP-SMA...