external ssd for imac 3d models
2233702 3d models found related to external ssd for imac.thingiverse
I use a external SSD for my iMac 27" late 2016. So I create a platform to lay the SSD down. ...I used metallic PLA.
prusaprinters
I use a external SSD for my iMac 27" late 2016. So I create a platform to lay the SSD down. ...I used metallic PLA.</p>
thingiverse
Hidden iMac holder for SSD external enclosure. ⚠️ Are you in a hurry to leave a tip? ...⚠️ Click the blue "
thingiverse
... screw it into this adapter. See the photo for reference. The print will fit on even pretty small printers since the tray itself is smaller than a 3.5" drive. This could work for other computers, but it's setup so the cables reach the SSD in an iMac.
thingiverse
Hi, This is SSD Enclosure Adapter Case for iMac (all flat-screen models from 2004 up to 2008). It's designed to replace the 3"1/2 HDD by a 2"1/2 SSD, including the plastic clip and the 4 screws. The SSD is intentionaly positioned close to the...
thingiverse
This frame enables the replacement of a HDD (3.5") with a much smaller SSD on iMac Late 2012. Maybe the frame also fits to other iMac models. Feel free to write me a message if you need the original model files (SolidWorks) or some small...
thingiverse
This is remix of Geoff Cohen/Root_ish's iMac SSD bracket to address the fit in a late 2009 21.5 inch iMac. ...I removed part of one of the brackets to fit around other computer components that blocked the fit in the original design.
thingiverse
This is an ongoing project for a mini SSD case for the Steam Deck, as I need to move multiple files around at all times. ... The body of a Sandisk SSD was used (make sure yours has the necessary dimensions) and a USB to SATA adapter.
thingiverse
An iMac mount for the Transcend (TS512GSJM500) external SSD drive. The mount is designed to slide down the back of the iMac's tapered pedestal into a secure position. ...This suspends the USB drive behind the computer, out-of-sight and off the desk.
thingiverse
iMac G4 SSD to Hard Drive adapter....it work with the stock iMac G4 screw, you just need 2x or 4x for the SSD to the adapter also use StarTech IDE/Sata adapter i try some 10€ one on amazon and nothing work.... if your iMac G4 freeze/stop/crash after...
thingiverse
updated the HD mount for the back of the iMac for my late 2019 27" imac and the two hard drives I constantly have attached. ...Tinkered it at: https://www.tinkercad.com/things/iioBb93Ef1X-lacie-imac-hd-mount
prusaprinters
This is the successor of https://www.printables.com/model/293801-samsung-t7-mount-adhesive-mounting and allows attaching one or two Samsung T7 SSDs to an iMac stand.The SSDs are clipped into the holder, the holder is then slid over the iMac stand and...
thingiverse
SSD External Case for USB use. ... Uses the StarTech.com Cable USB3S2SAT3CB Using a Samsung SSD 850 EVO 500Gb
thingiverse
This is a simple Samsung T5 SSD mount for your iMac. ...It hides the drives behind the display nice and neat.
thingiverse
Hide your SSD Samsung T5 by holding it on the stand of your iMac 21.5 "
thingiverse
I had to replace my old hard drive (3,5" HDD) in my iMac so i decided to put in an SSD instead of a new HDD. It's the 2015 version (EMC 2834), but this bracket schould fit in any iMac. For the Replacement I followed the instructions of ifixit. You'll...
thingiverse
I just put a SSD disk into an older iMac A1311 for a customer - he had purchased the SSD without realising these older (2009-2011) imac's use a 3.5" drive, while all SSD's are, of course, the newer and much smaller 2.5". I tried a few 2..5" to 3.5"...
prusaprinters
Mount on backside hole (use little force). Update: Noticed that holes are different, this version fits 21 Imac, 24 imac hole is little larger (you will have to scale model, or wait for updated version) Update: added version for 27 imac, its not fully...
thingiverse
... This one holds 13 SSDs. It should fit any external SSD from Samsung T5, T7, SanDisk Extreme (Pro) and alike. The inner dimensions of the compartments are 62mmx13mm. ... The Overhang on the long side is to number the SSDs with a Labelmaker.
thingiverse
I didn't like having the Sandisk Extreme SSD on the side of my Zcam E2 body, so I modeled a quick bracket to place it under the battery if you are using a rail system. This is a work in progress as I wait for more parts to make final measurements...
thingiverse
I had a simple USB SATA interface adapter that came with the SSD to clone the old drive to the new that worked perfectly for an external drive, I just did not have an enclosure to hold it all in, until now. This one was made with clear ABS and uses...
thingiverse
Normally the adapter supports 2280 drives and doesn't support the 2230 drives, because the case doesn't have mounting for these. So I made this tiny case for for 2230 drives only. Please use low power drives only, as there is no cooling. SSDs like...
thingiverse
i made an external ssd using a kingston UV400 480Gb ssd and a eminent ewent EW7017 sata to usb adapter. after fitting everything in the box and putting the top on it, i melted the side of the top to the bottom with a gas torch. i edited the top...