extruder motor 3d models

extruder motor(17hs3401) cable braket

extruder motor(17hs3401) cable braket

Anet 8 Extruder Motor Nema 17

Nice looking extruder motor rotation indicator :D

Support used for extruder motor with Bowden extruder

Cosmetic CAD model for a typical NEMA style extruder motor, popular with many 3D printers.

Replacement RepMan Extruder Motor Gear for RepMan 3.1 Instructions Print and drill holes.

Mendel Extruder Motor Mounts I wanted to move the extruder motors on my Mendel 1 to the end of the gantry bars like the Mendel 3, except they are made from wood. ... Use the 6x3x15mm pins in their holes in the mounts to stop the motor from falling.

If you've upgraded to Jon's no sag Y extender, this part is perfect for extra support to the extruder motor while still allowing the heat sink fan to function. ...It also allows space for some insulating tape to keep the heat from the extruder motor...

Simple Extruder Motor Holder for 20x40 aluminum profile. The motor will also cool by contact with aluminum profile. ... Please, be careful when assembling that the part does not break.

This extruder motor adaptor is made more strong and using a 25mm paper clip for better tension control. It's also easy to access when change material. ... Push fit connector was made in 5, 8 and 100 mm diameter.

I got inspired by another remix to adapt the Cali Cat's head for the extruder motor shaft for my Anycubic kossel linear plus. I cut off the body and made a hole in the back of the head to fit on the extruder motor shaft. The hole in the back is...

I do not like how Creality had both the X-axis and Extruder motors on the left side, which is quite a lot of mass, when compared to the right side that had nothing. I came up with a simple bracket that relocates the Extruder motor from the left...

3DP15 - Extruder Motor Holder for ADDME printers. This part is designed to mount a 25mm x 80mm heating jacket and 2x Nema 17 stepper motors for consistent syringe melt extrusion and retraction. Print no supports in current orientation. Use ABS...

... any of the extruder visualizers I've seen, so I've made my own. ...There are 4 different versions, I hope you like them. Remember to glue a 8x3mm magnet on the back. Oh and it should also work for other stepper motors, not just extruder motors.

Extruder motor mount to enable the use of CR10 style extruder gear ( https://www.google.com/search?client=firefox-b-d&q=cr10+extruder ) with a bowden setup. I'll post photos when installed. Installed on top of the right hand pillar. ...Screws changed...

Mount for Bowden extruder motor. Made with itopie MDF frames in mind (3/4") but they fit just fine on the extruded aluminum rails for the Anet AM8 upgrade. ...The handle it was modeled for came with the Anet A8/TronXY kits, but the screw holes are...

A bracket for the extruder motor of an E3D V6 Bowden Hotend to be placed on top of the left side by replacing the M3x18 screws with M3x30. Befor printing: rotate 90° in Slicer. ... Print Settings Printer: Anet A8 ...

I just discovered the joy of extruder motor indicators, and decided to make one myself! You will need to glue a 8x3mm magnet onto the smooth, flat side of the print. ... v1 - more industrial, sharp lines v2 - chamfered for that refined look ...

The upgrade features on the "Ender 3 pro" -Filament bending I have placed the extruder motor on top of the printer since the filament can sometimes bend and create bad print quality. -More stable printing Since the extrudermotor made allot of...

extruder Motor cooler fan brackets 40x40 mm i use M3 Bolts yuo can find it on ebay https://www.ebay.co.uk/itm/254106217100 conecting it from separate 12V pover supply,and using LED LM2596 Voltage Regulator buck converter module 4-40V in 1-35V out to...

Hello, Over time I noticed that the extruder motor was getting hot depending on the prints. The gear of the extruder made the filament soft and broke it ... Here is the solution and since then I have not had any problem. ... I connected to the...

Simple square with a groove to mount the extruder motor at an angle on a 20x20. The groove allows to adjust the angle of the infeed. Designed for an Anycubic kossel Plus, but valid for any printer, especially deltas. An extra M4 screw and nut is...

I just discovered the joy of extruder motor indicators, and decided to make one myself! ...You will need to glue a 8x3mm magnet onto the smooth, flat side of the print.</p> <p>v1 - more industrial, sharp lines<br/> v2 - chamfered for that refined...

... almost every extruder setup. - The whole design is 80gr lighter than regular NEMA 17 Extruder Motor Check the other gearbox designs: https://www.thingiverse.com/thing:3626993 by BunnyScience https://www.thingiverse.com/thing:3714978 by vertigo235

This is an extruder motor mount that I designed to use with an e3d extruder. It mounts on top of the frame in place of the spacer for the led board. I also included a picture of my filament holder mod that I did as well. I drilled a 5/16" hole in the...

As everyone knows, the extruder motor on the Prusa i3 runs hot. I wanted to add heat sinks, but have heard of the thermal adhesive not sticking long and them falling off. This heatsink clamp adds compression to the two side heatsinks, pressing them...

05/17/2020: Updated STL for a better and more functional fit. A simple extruder motor indicator, but in the form of a triforce. It doesn't need to be printed in multiple colors, but it is modeled in a way that the main triangles are further out from...

This is a remix of this:https://www.prusaprinters.org/prints/72931-extruder-motor-cooler-mk3s-by-simonpkwhere I have added threads for the PTFE-tube mount as I didn't want to glue it on.The reason I wanted an extruder motor cooler is due to my...

This is a 4.36:1 planetary gearbox intended to be inserted between your NEMA 17 extruder motor and your extruder mechanism. This allows you to use your existing Airtripper or similar extruder and your MK7 drive gear with a 5mm bore, yet still insert...