eyetoy 3d models
23 3d models found related to eyetoy.thingiverse
A base mount for [Banapfel's EyeToy camera mount](https://www.thingiverse.com/thing:2363086/remixes) using [C3D_Miguel's rubber feet](https://www.thingiverse.com/thing:3020865) to connect ot the CR-6 rails.
myminifactory
This is an Playstation 2's EyeToy holder to mount it in the top of your screen. ...The gap distance of mount is 13mm, but you can remix it in order to fit your setup.
thingiverse
This is an Playstation 2's EyeToy holder to mount it in the top of your screen. The gap distance of mount is 13mm, but you can remix it in order to fit your setup. ...
thingiverse
This is a simple wall mount for the PS2 EyeToy camera, which I'm using with my OctoPi. The two screw holes are 3mm in diameter. ... Print it upside-down and you won't need any supports.
thingiverse
I made this tension fit mount for using my eyetoy to monitor my prints. As far as cam quality, it's probably good enough to see if it's a mess, but no real details. Works really well with my FFCP mount. Intended to be used with a #8 UNC - 32 nut and...
thingiverse
EyeToy PS2 camera mount for Artillery Genius. ...Remix of https://www.thingiverse.com/thing:4257585 and https://www.thingiverse.com/thing:2363086
myminifactory
This is a support to mount a led ring on an old PS2 EyeToy Camera. ...I made this to use the camera with octoprint and see the print in the dark.
thingiverse
These are adapter cases for PS2 EyeToy cameras to fit in some PS3 Eye camera holders. I have an old EyeToy camera and still don't know if I wan't to upgrade to a PS3 Eye. So I tested some PS3 Eye related Holders for my Ender 3 and noticed that the...
thingiverse
I made this support for a 8mm LED ring to mount on a EyeToy PS2 camera for OctoPi. With this support and its position you can see the printer working even in a totally black room. You have just to sand down a bit the model for a perdect fit on the...
cults3d
I made this support for a 8mm LED ring to mount on a EyeToy PS2 camera for OctoPi. With this support and its position you can see the printer working even in a totally black room. ... You have just to sand down a bit the model for a perdect fit on the...
thingiverse
This is a mount for an old Sony EyeToy camera to mount this camera to your Anet A6 or A6. For mounting you have to remove the backplate of the camera (the screws are under the sticker with informations) and also the small screw in the backplate. I...
thingiverse
I made this support for the arm I remixed. ...I found that camera taking dust, so I decided to use it with OctoPi because it is supported with stock configuration for the camera.
cults3d
I made this support for the arm I remixed. ...I found that camera taking dust, so I decided to use it with OctoPi because it is supported with stock configuration for the camera.
thingiverse
Ikea sells these bright led press on and off usb lights, two pack for 7 euro. Made a tripod mount for the PS eye toy and a plate to attach the Ikea lights to. Lights come equipped with double stick tape and have a long usb cord. Used petg only...
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515
thingiverse
... for the screws have a "counter sink" to avoid swapping out the stock screws for longer ones. ... Print this with my EyeToy camera mount, or use it with anything else. Link to EyeToy-to-printer bracket mount: https://www.thingiverse.com/thing:4740310
thingiverse
This is a Mount for my PS3 EyeToy Camera to Clip it on my Printer with aluminium profiles. I Printed it with the Cura Tree Support and it work fine. ... I Made this for a 20mmx40mm Nut6 Profile.
thingiverse
I wanted to put a LED Ring (WS2812B) to my Playstation 3 EyeToy camera wich i use with Octoprint. ...For this i created a holder with works just by pressfit.
thingiverse
The bottom "webcam stand" mount is based on the "EyeToy holder (webcam)" slightly reduced for a tighter fit. The sliding top mount is based on the "FFCP Creator Pro EyeToy Mount". ... Printed in PETG with 25% fill and 4 perimeters but should print...
thingiverse
I made this quick, simple adjustment ring to snap onto the bottom of my Playstation Eyetoy webcam to stiffen the adjustment of the camera angle. Any slight bump or wiggle would move the camera and it became very frustrating during remote prints. ... ...
thingiverse
This is a remix of the Banapfel's item: https://www.thingiverse.com/thing:2363086 I changed the original design to fit on the bottom part of the printer, beside the bed, and expanded the support base of the camera to make it compatible with the black...