ezreal rework 3d models

To attach my printed dragon fan (from http://www.thingiverse.com/thing:26310) on my Prusa I3 Rework extruder, I was inspired by another design (http://www.thingiverse.com/thing:198186). I chose 0.2 mm layer height and 20% infill for printing, using...

I swiftly reworked the front section to accommodate mounting my induction sensor. Initially, I had secured it to the side using a different mount that was unfortunately glued on, but this approach ultimately failed. I've since replaced it with zip...

This addition enables the attachment of any Budas-style hotend to the Prusa i3 Rework extruder (available at http://www.thingiverse.com/thing:119616). Secure it using two M3x40 screws. ...Though not yet confirmed functional, it has been printed, tested,...

This is a bracket for integrating a Raspberry Pi B+ into a Microdelta Rework from EMotionTech. Perfect to embed OctoPrint directly into the printer and use it on wifi. There's no need for screws, just 2 washers, 2 nuts, and 4 small plastic clamps. ...It...

This is a replacement impeller for the Quick 861DW digital rework station. Apparently these break quite a bit, and are very hard to get replacements. You will need to reuse the metal top piece from the broken impeller. If the shaft is too tight, you...

Adjustable fan duct for Prusa i3 rework. It consists of three parts: a duct to mount a 40 mm fan; a rod; and a holder that mounts on the two bolts blocking the extruder. Print Settings: Resolution: 0.2 Notes: ...

lorsqu'on remplace la tête hexagon sur micro delta rework par une E3D cette cale d' épaisseur permet de descendre les ventilateurs de refroidissement pour être à une bonne hauteur à insérer entre le ventilo et le support de tête, l'encoche vers le...

The Prusa Rework Carriage has been modified to utilize LM8UU bearings. Two files are provided for the Geeetech printer, one with endstop and another for standard carriage use. ... Print Settings: Printer Brand: RepRap Printer: Geeetech i3 Rafts: No...

This is a replacement Y motor mount designed specifically for the Prusa i3 Rework, featuring an integrated stabilizer block to prevent bending of the plastic mount under motor forces. ...Additionally, I eliminated the unnecessary endstop mount as I...

This is a bracket for integrating a Raspberry Pi B + into a Microdelta Rework from EMotionTech. Perfect to embed OctoPrint directly into the printer and use it on wifi. There is no need for screws, just 2 washers 2 nuts and 4 small plastic clamps .

This piece helps hide the second extruder hole on the micro Delta Rework if you only have one extruder. It won't improve print quality in any way, but rather gives the micro Delta a more appealing look based on my personal taste. --- The FreeCAD...

un support pour ADXL345 pour resonnance sur Klipper pour Microdelta Rework va sur l'emplacement de la z-probe et j'utilise deux vis m3 et deux nuts m3 (les nuts sur le dessus, les vis par dessous) pour le fixer en place sur le mount print sur Cura en...

Inspiration for this design stems from the following source: http://www.thingiverse.com/thing:119616 In response to feedback and concern over interference with a P3steel frame screw, an updated version of the reworked Prusa i3 is now available for...

I bought a JCD 8898 750W SMD soldering rework station from Aliexpress (https://www.aliexpress.com/item/1005002697062960.html) but it did not include a holder for the soldering iron. I created this mount and holder to store the iron away after use. ...

Print Settings ============== Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: Printed with MatterControl 1.5 Basic settings with above resolution and infill. Printed with $5 filament's...

... printing software. Print Settings: Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Notes: Printed with MatterControl 1.5 Basic settings, using a $5 filament's Rainforest Green Adv. ...Ingeo PLA.

This is also the fan duct included in the reprap Wilson design, and I'm copying it here in case any Rework users want to give it a try. I designed this in Sketchup to improve airflow at the extrusion point, with some air also directed at the top of...

Prusa i3 Rework Extruder sensor bracket for 12mm inductive/ capacitive sensor Print Settings Printer: big printer Rafts: NoSupports: Yes Resolution: 0.26Infill: 60% Category: 3D Printer Parts

This is a rework to eliminate the need for screws when getting to the hot end. It incorporates a magnet that attaches to the screws of the bracket already used by the printer. It allows quick attach/detach for access to the hot end. I used a 5.2mm x...

I recently purchased a rework station that came equipped with 8 tips for my soldering iron. The stand for the iron features slots on each side to accommodate the tips, but can only hold a couple of them horizontally. To keep them organized and...

Prusa i3 Rework Extruder sensor bracket for 12mm inductive/ capacitive sensor. Print Settings Printer: big printer Rafts: NoSupports: No Resolution: 0.30Infill: 60% Category: 3D Printer Parts

Mount the E3D v6 to your Prusa i3 Rework using two M3x30 screws and two M3 nuts to secure both parts firmly in place on the E3D. Next, attach the E3D to the extruder body with four M3x12 screws. ...Print settings: speed at 50 mm/s, layer height of 0.1...

I'm excited to share my latest project with you - a reworked version of the Noyau Micro Delta design specifically tailored for the E3D-v6 hotend. This new iteration is all about maximizing performance, reliability, and ease of use, while also taking...

A simple wedge I crafted in Solidworks 2014 aims to strengthen my Y motor, specifically designed for the Rework version of I3 printers with 10MM all threaded rods. It fits perfectly and performs exceptionally well. Inspiration came from...

Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.3 mm Infill: 30% Notes: Printed in PLA. ...Post-Printing Shopping list: 1 x length of M8 threaded rod 6 x M8 nuts and washers 2 x 608zz bearings 2 x M4 x...

This accessory is specifically designed for use with Prusa i3 Rework version. It helps cool down prints and bridge large gaps effectively. To install, you require 5-M3x15 or 16 screws and nuts; four for fans and one for the fan holder. Note that...

Prusa i3 Rework Extruder sensor bracket designed specifically for a 12mm inductive or capacitive sensor. Print Settings: Printer: Utilize your big printer to achieve precise results. Rafts: Leave the raft option unchecked, as no raft is...

X Axis Endstop support for Prusa i3 Rework Printer Settings Print settings are optimized for the RepRap Prusa i3 Rework printer, a highly versatile and reliable model that is well-suited for a wide range of printing tasks. To achieve optimal results...

Just my Rework of DIY_Machines Excellent , Easy 3D Printable CNC Drawing Machine https://youtu.be/5DDamrDog6M Be sure to watch DIY_Machines Excellent easy to understand VIDEO'S Video guide for assembly instructions here: https://youtu.be/XYqx5wg4oLU...

Just my Rework of DIY_Machines Excellent , Easy 3D Printable CNC Drawing Machine https://youtu.be/5DDamrDog6M Be sure to watch DIY_Machines Excellent easy to understand VIDEO'S Video guide for assembly instructions here: https://youtu.be/XYqx5wg4oLU...