ezstruder 3d models

This is a knob designed to be used with the EZStruder from SeeMeCNC. It allows you to easily see how the extruder motor is moving, and can be used to manually feed or retract filament. Please be sure your steppers are turned off before manually...

I like the new EZStruder from Seemecnc, but I miss watching the gears of Steve's Extruder to see that it is working properly. I made this silly little indicator and it does the trick. The STL file has the hole dia at 5mm. ...Its a press fit on the motor...

This will adapt the planetary geared stepper from TriDPrinting.com to a SeeMeCNC EZStruder. It should work with the newer EZRStruder as well, as they both have the same hole pattern. Uses four M3x13 screws, plus the ones that come with the...

Instructions Fan shroud can be printed with 2 perimeters and 0% infill, mount with screw and nut from EZStruder. Need extra screws for mounting the fans. Adapter can be printed with 20% infill or more, mount with original BI cold-end screws. ... I...

It is the first version, so consider the holes as pilot holes and open them up per your choice of fasteners, If using the Ubis hotend, the EZstruder will require a little dremel-type work to accomodate the Ubis's chamfered slot. ...The position of the...

This is a little indicator that goes on the end of the EZStruder shaft so you can see how fast it's extruding and when it retracts filament. ... Instructions Made with 2 shells and 100% infill.

Summary This is a little indicator that goes on the end of the EZStruder shaft so you can see how fast it's extruding and when it retracts filament. ...Instructions Made with 2 shells and 100% infill.

Replacement cover for the EZStruder on my Rostock Max V2. The original cracked in two due to a very weak spot in the brittle plastic. ...This design has a bit of reinforcement in that spot.

This thing is a simple mount, which allows a SeeMeCNC EZStruder direct drive extruder to be used with a standard Prusa X-Carriage with 50mm hole spacing. It's rotated to give clearance for the hot end, and the height was selected in order to allow...

The stepper itself is attached only to the EZstruder, so I also added a tab/shelf to support the bottom of the stepper. Instructions I printed the part on a MakerBot Dual in ABS with three shells and...

This is for mounting the SeeMeCNC EzStruder on the frame of the Rigidbot 3d Printer for use with a bowden setup. This is still a work in progress and I may add an angled version. FYI. ...The mounting design was inspired by this...

... head M3x6mm screws, this means you don't have to disassemble the top of the Kossel to insert the additional nuts. ... I've also added two recesses on either side to give some clearance for the extruder wires while inserting/removing the EZStruder.

It goes on the end of the EZStruder so you can see how fast the motor is spinning and when it retracts. I thought it would be pretty cool to paint it yellow and black like the original symbol. I have the Pro-E prt file if anyone wants it, I...

Based on the EZStruder Knob by h3ss I added a notch to his design which mates with the notched portion of the stepper, allowing for better contact and more force to be exerted on the filament during hand extrusion. I also closed off the back as a...

I had a few gripes with the stock EZStruder knob (which looks like a gear) in that it was too small of a diameter, was too close to the motor and wasn't easy to tell how fast the motor was turning by watching the knob. So I put this together with...

Instructions I didn't mark down which screws need replacing, but you'll find that some of the original screws for the ezstruder will now be a touch too short. The cylinder that replaces the aluminum one in the original has BSP threads for the...

I also include the picture changes i made to the originally included ezstruder for room of the pulley. it prints faster than to modify the original back plate. also you will need to rotate the bottom end 180 deg, and use the other side to hold the...

Bracket to mount an EZStruder (and stepper) to an OpenBeam extrusion at a 45 degree angle. The spacer is optional, depending on whether or not you need additional clearance for wheeled carriages. Print the bracket at with high infill due to the...

Run the button head M3*40mm bolt from the back of the EZStruder, then secure with the knurled nut and tighten. Then add washer, fan bracket, washer, and thumbscrew and tighten hand-tight. Ensure the bottom of the duct does not drag against the work...

I was having issues with my EZstruder slipping trying to grip filament so I wanted to increase the grip by increasing the tension caused by the spring. So I just created a 2mm spacer that the spring can rest on. It gives it enough torque now that if...

EZSTRUDER Special Rostock / Delta / Orion Same SeemeCNC

Graber i3 Ezstruder Mount with attachment for 50mm fan.

Snap on mount for SeeMeCNC's EZStruder for upgrading your Prusa to Bowden. Slips in place very easily and locks in with a short piece of filament inserted in the end. ...Uses hardware the comes with the EZStruder.

NO supports needed, but there is some bridging so don't go too fast For attaching to the top plate I used 30mm M3 socket cap screws & nuts, and for attaching the EZstruder I used to stock screws & nuts. I would recommend much shorter (10mm?) M3...

(Disclaimer; I also changed the filament diameter from 3 to 1.75 and the hotend nozzle from 0.5 to 0.3mm, so the extruder may not have been the only contributor to my problem) Instructions Required; 1 x EZStruder 4 x M4 x 20 Screws 4 x M4 Nylock...

... to mount a SeeMeCNC EZStruder direct drive extruder [1] onto a standard Prusa i3 x-carriage with 30mm hole spacing for the extruder mount. ...Print and enjoy! [1] http://shop.seemecnc.com/EZStruder-Cold-End-Kit-70780.htm Category: 3D Printer Extruders

I've converted my ORD Bot Hadron to use dual extruders built on the EZStruder. ... These are the mounts I designed for the job.

This thing is a simple platform, which allows one to mount a SeeMeCNC EZStruder direct drive extruder [1] onto a standard Prusa i3 x-carriage with 30mm hole spacing for the extruder mount. Print and enjoy! ... [1]...

This is a slightly improved version of the BeKossel EZStruder Mount (Credits for the original concept go to whomever - the BMP-Image referred to no source). All dimensions are designed to fit the 15 mm OpenBeam profiles. EDIT: added a new version....

Instructions BOM (for 1 EZStruder and fan) 5 x M3x20mm socket screw 1 x M3x30mm socket screw (use 3 flat washer or cut the screw) 5 x M3x16mm socket screw (or 15mm or even 20mm) 4 x M3 nut 1 x 40mm 12V fan PRINTING Print in ABS (motor gets hot),...