f mount lenses 3d models
365961 3d models found related to f mount lenses.thingiverse
This cap is designed to fit on the back of Nikon F-Mount lenses. Its design is quite close to the original and it is quite sturdy. Instructions This cap's design is close to the original. It is very...
thingiverse
Stand inspired by Nikon logo, to safly store / display your Nikon lenses. ... Instructions Print with layer height of 0.30mm or less.
thingiverse
Fits Nikon F-mount bodies and Minolta SR-mount lenses. Built in a jiffy for reasons of curiosity. Watch this demo of the 80mm adapter with a 50mm F2 lens:http://youtu.be/D8-BCeOGRiQ Strictly a Nikon user? ...I've got a full set of Nikkor macro...
prusaprinters
Fits Nikon F-mount bodies and Minolta SR-mount lenses. Built in a jiffy for reasons of curiosity. Watch this demo of the 80mm adapter with a 50mm F2 lens: http://youtu.be/D8-BCeOGRiQ Strictly a Nikon user? ...I've got a full set of Nikkor macro adapters...
thingiverse
Stand for nikon F-Mount Lenses It allows you to keep the lens vertical and you can leave it with the original cap mounted
thingiverse
It projects current time to the wall or ceiling of dark environment such as bedroom. ...Nikon F-mount lens (lenses for Nikon SLR) and micro:bit are used.
thingiverse
Fully printable lens cap for Nikon F-mount lenses. Has been tested with: Nikon 14-24mm AF-S Nikon 27-70mm AF-S Nikon 70-200mm AF-S VR II Nikon 16mm AF-D Nikon 50mm AF-S Provides good grip and a snug fit. No sanding required. ... Designed from...
grabcad
F-Mount lenses on your S. ...NX cameraobviously there is no data transfer between camera and lenses,thus you only can mount lenses with mechanical adjustmentit has a very tight fit, so you might have to do some reworkingMy latest Version even has a...
thingiverse
Some pinhole camera lenses for Sony E-mount mirrorless cameras. I designed this for the A6000 but it will work with any E-mount camera. All you need to do is put a small piece of aluminum foil between the lens and the "snappysnap" and then use a...
thingiverse
The original design was a macro lens adaptor for Nikon F-Mount lenses, and I didnt change the ends that attack, so it should connect well. The smaller spacer has an angle of about 4 degrees to the left, and the height is about 24mm. The larger...
thingiverse
Ordinary rear lens caps for Nikon F Mount lenses hold to the lense's bayonet by FRICTION. This rear lens cap LOCKS to the lens using the camera body's standard lens locking mechanism. ...
thingiverse
I needed to organise my lenses for my DSLR camera and thus produced these holders for the IKEA KALLAX shelves system. However, they should work for organisation of lenses anywhere. They are printed in PETG for strength and no supports are needed.
prusaprinters
Wow! You can now give any Nikon F-mount lenses or adapters a super macro super power! UPDATE: Added a new retention ring for lens-side mounting.No tools or rubber bands needed! Just snap it onto any macro adapter and check that its protruding tip...
thingiverse
You can now give any Nikon F-mount lenses or adapters a super macro super power! UPDATE: Added a new retention ring for lens-side mounting. No tools or rubber bands needed! Just snap it onto any macro adapter and check that its protruding tip...
thingiverse
Belt mount for Canon lenses Canon EF mount very comfortable and strong to exchange your lenses. ... The piece Canon_ef_part_3 must be printed twice
thingiverse
Lens cap for E-mount Sony Lenses, with alignment indicator, and rotation end stops. Tested on Sony 16-50mm Kit Lens and Neewer 35mm f/1.7 Lens. ...Tight fit for longevity.
thingiverse
Extension Tubes for Sony E-Mount Lenses. With alignment indicators and locking hole. Designed to lock with each other, as well as be a tight fit for lenses and camera body. Tested on Sony 16-50mm Kit Lens and Neewer 35mm f/1.7 Lens, and on a Sony...
thingiverse
Rear lens cap for L mount lenses. ...Tested on and fits all my various Sigma and off-brand L-mount lenses and adapters.
myminifactory
These lenses, usually marked between f/0.75 and f/1.6, typically have no aperture iris, no focus mechanism, and a giant external screw thread intended for mounting. They generally can't focus to infinity even on a mirrorless body, and IQ is scary...
thingiverse
This is a cover to protect the rear part of C-Mount lenses, I recommend to use flexible material to avoid leave residual material on lenses.
thingiverse
These lenses, usually marked between f/0.75 and f/1.6, typically have no aperture iris, no focus mechanism, and a giant external screw thread intended for mounting. They generally can't focus to infinity even on a mirrorless body, and IQ is scary...
thingiverse
Simple Oculus wall mount that doesn't have a risk of scratching your Lenses when placed upon the stand. ... I'm honestly surprised I couldn't find one of these on here already...Seems pretty obvious to me.
thingiverse
An openSCAD script generates extension tubes for c-mount lenses. Made with the tolerances required for a low-resolution (0.3 mm) printer. Lenses should thread in tube without printed threads. UPDATE: Tweaked the measurements to fit snugly on lens...
prusaprinters
Rear lens cover for Mamiya-Sekor 80mm f/2.8 and 105mm f/3.5 lenses. May also fit other models with 31mm diameter of rear lens elements. ...Please let me know what other lenses work and I will update the description
thingiverse
Customized version of http://www.thingiverse.com/thing:90674 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=90674 Instructions Using the following options: $fn = 66...
thingiverse
Customized version of http://www.thingiverse.com/thing:90674 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=90674 Instructions Using the following options: $fn = 66...