f210 3d
1609552 3d models found related to f210 3d.grabcad
Depending on what material is used to 3D print, highly recommended to use reinforced versions as 3D print material may not be as strong as polycarbonate if printing the original replica.WARNING : Be informed of your print material and its application...
cults3d
For all Walkera F210 UAV pilots, propeller breakage can become expensive, especially since the Walkera F210 propellers are fragile and quickly broken. Here is an exclusive file to print your Left propellers yourself. Printed in PLA, does it fly...
cults3d
For all Walkera F210 UAV pilots, propeller breakage can become expensive, especially since the Walkera F210 propellers are fragile and quickly broken. Here is an exclusive file to print your Left propellers yourself. Printed in PLA, does it fly...
sketchfab
sculpture F210. ...Symbol (F) - MUSEUM SCULPTURE - TEMPLE PLACE 3d photo capture by nexus 6p.
thingiverse
Depending on what material is used to 3D print, highly recommended to use reinforced versions as 3D print material may not be as strong as polycarbonate if printing the original replica. WARNING : Be informed of your print material and its...
cults3d
the ultimate propeller protection for your Walkera F210 drone Equipped with foot, it is fixed in place of the original feet
thingiverse
This is a support for LED lights on the Walkera F210 racing drone. Just glue them on the arms and attach your LED lights to them. ...Enjoy!
thingiverse
... the front guard. DONE ADDED! 4/2 Link to my other Walkera F210 Parts -> https://www.thingiverse.com/thing:4716360 Check out the reinforced feet, been running one set through a ton of crashes and have not broken one yet! ...New pilot (enough said)
thingiverse
This is to allow bigger batteries to be easily used on the Walkera F210 racing quad.
thingiverse
(LOTS!!!) -ANTENNA MOUNTS: I removed these from my drone completely and went low tech with a ziptie and some shrink tube (photo) (nothing to break or swivel into the props.) This is a collection of 3d parts I designed for my Walkera F210 racing...
thingiverse
The Cainda F210 microscope as supplied by Amazon is a very loose fit in its stand attachment ring (see image 1). This simple split spacer slides over the microscope and fills the gap. It has channels either side to help clear the control buttons...
grabcad
Com intuito de facilitar O Trabalho dos demais Projetista that here PRESENTES Neste local, Estou disponibilizando Desenhos de itens that possam sor Úteis em Equipamentos Projetados Pelos demais.
thingiverse
Support Runcam 3S for Walkera F210. It is hold with the battery, but you can put the glue in several places to have less vibration. It is necessary to cut a little the canopy camera not to disturb the support. At the back, I made a simple piece to...
thingiverse
This is an ESC cover for the Walkera F210 racing drone. It covers the full ESC from damage. It is vented to let the heat from the ESC's disperse. Enjoy! Edit: I have uploaded V2 of my guards. ...They have a little bit of a different style.
thingiverse
This is a 2 part captive Foot and motor guard for the F210 Walkera Quad. The guard goes on first, then the foot holds it in place, this uses the original length screws, and can take some hard landings. for the foot you want to print plate down and...
thingiverse
Replacement Motor Guards & Feet. ...Also an option for longer feet if you're attaching a gimbal & camera beneath your F210
thingiverse
This is for adding a Sony AZ1 Action Cam to your Walkera F210. ...https://youtu.be/ntpB5zFatrY
thingiverse
As the original cam of the F210 is a bit "old", I created this cam holder for a 1000 TVL. I already have good experiences with this cam in a R110, so I also did it in the F210. Works great. You just need to cut the microphone and cable. ... ...
thingiverse
This is a simple camera adapter for FPV drone Waklera F210 to mount RunCam Racer 2 or 3. Works fine as you can see. The plug panel for the joystick can be added just behind. Enjoy! ... Hans
prusaprinters
A mount to adapt your HP f210 dashcam to position it in the rear window of a ute/pick-up truck or van.Requires modification to the mount that comes with your dashcam.I have printed the parts in PETG and they have survived a summer in Brisbane,...
thingiverse
This is an attachment to hold a GoPro session camera on the battery cover that I made for the Walkera F210 Racing drone. It fits over the battery cover and clicks into place. Although it is a pretty tight fit I would make sure to glue it to the...
thingiverse
This is an attachment to hold a GoPro style camera on the battery cover that I made for the Walkera F210 Racing drone. It fits over the battery cover and clicks into place. Although it is a pretty tight fit I would make sure to glue it to the battery...
thingiverse
Befestigt wird das ganze mit längeren schrauben aus dem schraubenset von walkera
thingiverse
(Edit: v2 files use standard 16x19mm bolt spacing. they were shy 1.33mm and made bolts crooked. i should have measured them beforehand.) *Fixed the model mesh to make the files one solid model instead of two which causes print and structural...