fan duct flashforge 3d models

120mm Fan Duct - Flashforge Dreamer front door

http://www.thingiverse.com/apps/customizer/run?thing_id=373491 Instructions Using the following options: duct_shape = squared duct_border_width = 2 duct_delta_y = 5 duct_delta_x = 0 fan_size = 120 base_screw_diameter = 4.3 duct_length = .70...

Simplified bracket for Active Cooling Fan Duct - FlashForge (Slightly Angled)

This is remix of bracket: http://www.thingiverse.com/thing:350649 I slightly angled the mounting to compensate the weight of the fan duct because I noticed when I attached the duct it not perfectly level or parallel on the bed plate. ...Also extend the...

Remixed Fan Duct Design-Flashforge Creator Pro

This is much better than the Flashforge duct as this one cools both hotends. Print Settings Printer: Flashfore Rafts: ...

Dual fan duct for FlashForge Adventurer 4

I have mirrored the file, extended the segment for the catch(duct side) and increased the height of the opening of the fan duct fo fit the Flashforge Adventurer 4. I am currently printing a test version and will try to fit it on my AD4 once i...

Dual fan duct for FlashForge Adventurer 3

I've designed a dual fan duct that splits the flow so that both sides of a print are cooled. The results speak for themselves. The original duct is on the left in the overhang tests. Ignore the top few layers. The modelled curled up so much the...

Optimized Fan Duct for Flashforge Adventurer 3

This cooling duct is intended to be used as a replacement part to the OEM found on the Flashforge Adventurer 3. It's been designed in a way that optimizes the air-flow path to maximize cooling (the OEM design has a kink in the flow-path that would...

Simplified bracket for Active Cooling Fan Duct - CTC / FlashForge

This is a bracket to attach my Active Cooling Fan Duct to a CTC or FlashForge printer without the need of the rarely available M3x60 bolts. A second benefit is that you can click in and out the front cooling duct without any tool and without loosing...

Dual Fan Duct for FlashForge Adventurer 3 - remix reefwarrior

This is a small adjusted model of the Dual Fan Duct of reefwarrior (https://www.thingiverse.com/thing:4394702). As already mentioned in the comments of the original model of martin_au the model is a little bit too large to fit well for at least the...

Active Cooling Fan Duct for Flashforge (/Replicator1 / Duplicator 4)

This is a remix of http://www.thingiverse.com/thing:295317 I wanted to fit in a 60[mm] fan to have a similar airflow at lower RPM which results in lowered audible noise and lowered vibrations. Do note that depending on your 'homing' settings this...

40mm to 50mm Fan Adaptor for 50 mm Heavy Duty Layer Fan duct - FLASHFORGE Creator X (MakerBot Replicator Dual, CTC and more)

... to make an adaptor for this design, as i like the design but i had no 50mm fans. ...i guess it would work for other designs, where a 40mm fan is to be fitted in a 50mm fan hole. ... its tight enough for no need of screws to fit, compression fit.

Rear Mount Cooling Blower Fan Duct for FlashForge Creator Pro - Remix/Mashup

... plate removed. Print Settings Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: Yes Resolution: .15 mm Infill: 15 % Notes: Very few supports needed, only where the M3 nut openings are and under the pin that holds the blower fan on.

50 mm Heavy Duty Layer Fan duct - FLASHFORGE Creator X (MakerBot Replicator Dual, CTC and more)

==> READ THIS !

Fan Duct for FlashForge Creator Pro with Flexion HT Dual

This is designed for use with the Flexion HT extruder upgrade on the flashforge creator pro. The mods I made were stretching the tube which reaches to the 2nd nozzle further away from the heater blocks to avoid them getting hot and drooping, also,...

Fan Duct Right only flashforge

It's a remix of the dual fan duct by DrLex, I need a fan duct for right extruder only, this is very useful when you do not have time or spare to repair the left (ptfe burned for example).

Flashforge Creator Pro Fan duct

This fan duct is designed and made to fit a Flashforge Creator Pro, the cooling of the fan allows the machine to print in PLA too. ...it is very easy to assemble and easy to snap into place on the carriage. Everything you see in the images is inlcluded...

Flashforge Dreamer dual fan duct

Looking for a dual fan duct for my Dreamer I got inspired by this [Blower/ Turbo Flashforge Creator Pro Part Cooling Duct remix](https://www.thingiverse.com/thing:2826878). This is a very nice solution, but in the Dreamer there's no place to install...

Flashforge Dreamer NX fan duct

Dreamer Nx fan duct, as original. Print in petg or similar for higher heat resistance. Supports are required from the bed, and possibly internally, dependant on your printer/settings, but can easily be removed later. ... I couldn't find the part...

flashforge guider IIs fan duct

Fan duct for a guider IIs. The opening has been enlarged to accomodate different heater blocks that use e3d v6 nozzles. ...(much cheaper) Support is needed under the screw holes.

FlashForge Creator Pro Wrap Round Fan Duct

... the fan attachment. ...   The benefits to the finished product with the addition of a fan and duct to direct the airflow are quite significant - so I've designed this fan duct to help others acheive better prints when using their FlashForge. ...  

CTC & Flashforge PLA Cooling Duct Fan Clips

I was really a huge FAN (pun-intended) of thruit00's v2 PLA fan clip duct design, but on the CTC Creator I noticed that the vent outlet was actually rubbing/touching very snugly against the heating blocks causing sagging and warping of the vents...

Flashforge Creator Pro Single Extruder Fan Duct

Flashforge Creator Pro fan duct for single extruder usage leveraging the standard blower fan. Exhaust gets really close to the heating block so you should use a silicone sock on it to prevent the exhaust from melting. Printed in PETG with...

Flashforge Adventurer 3 Dual Fan Duct Voxel

I was looking for a good fan duct for the adventurer 3 as the original is rubbish. ... downloaded a few different ones from here and tested them (see here for results) I then came up with this and think it takes the best bits from them all and gives...

Flashforge Adventurer 4 Fan Duct replacment

A drop-in replacment for Flashforge Adventure 4 fan duct. ...Print the two parts in PTEG or ABS an glue together with super glue.&nbsp;</p><p>&nbsp;</p><p>Remix from https://www.thingiverse.com/thing:5244614&nbsp;</p><h3>&nbsp;</h3><p>&nbsp;</p>

CTC & Flashforge PLA Cooling Duct Fan Clips

I was really a huge FAN (pun-intended) of thruit00's v2 PLA fan clip duct design, but on the CTC Creator I noticed that the vent outlet was actually rubbing/touching very snugly against the heating blocks causing sagging and warping of the vents...

FlashForge Creator Pro Cooling Fan Duct

Edit: Added the dual 40mm fan version (never made it, if there's any problems and you don't have Solidworks let me know and I can edit the file) Instructions It was printed with ABS at 240C extrude temp with the build plate at 115C. I didn't use...

FlashForge Blower Fan Duct and Mount

FlashForge Creator Pro filament cooling fan duct and mounting plate to mount at the end of the cooling bar. Print Settings Rafts: No ...

FlashForge Creator Pro - reversed fan duct

This duct serves as the spacer, the fan housing, and the fan duct. I install the duct with the original 35mm screw, then install the fan, and yeah no extra 5mm needed. You can still mount the fan to the cartridge, but this way: you will need 2 very...

FlashForge Creator Pro front dual fan duct

This is a drop-in replacement fan duct that fits the FlashForge Creator Pro and similar models that have the ‘turbo fan’ at the left of the nozzles. It has been confirmed to fit the 2015 FFCP (upwards opening door), the 2016 (sideways door), and the...

Flashforge creator pro front fan dual duct

I added a second mounting hole and adjusted the Ducts so they line up with my FFCP..

FlashForge Creator Cooling Fan Duct - SSW Mod

If you have a custom case, be aware that the fan extends past the outer body of the printer (may collide with your custom door) I connected some resistors up to the fan to limit the output and also a power switch to shut it off. The combination...