fan duct for noctua nh d15 in combination w tall memory modules 3d models

I noticed, after printing the original version, that the noise-suppressing pads on my 40mm Noctua fans where being pushed out and around the corners of the duct where the fans rest. Easiest solution: I squared them. I don't know if it's good or...

... the fans to fit noctua 40mm fans, as they have sharper corners. ... I also added mounting holes for securing the fans with M3 screws. EDIT 05.02.2021 Added: DUAL_4020mm_ADKS_Fan_Duct_Body_Remix This version fits 4020 mm Fans in the front AND on top.

Suggested print settings: no rotation - designed to be printed on bottom, support for 80°/10° overhang, depending on your slicer, 6 perimeters, detect small walls on, Support: - z distance 0.15mm / xy distance 1mm / z over xy - type zig zag, 1.5mm...

This duct works well if the printer has the elastomer feets sold on Prusa-Box's website.I've also made two grills:- one for fixing the fan with screws (it has countersink holes)- one for fixing the fan with the NA-AV3 rubber anti vibration mounts...

This fan shroud/filter holder allows fitting of the Noctua fan and is also snug enough that no screws are necessary to hold it in place. This should be printed upside-down, with supports enabled. I made mine out of ASA and it deals with the...

I edited this to allow for a ribbon to pass-through for a camera, two 40mm Noctua fans, and a USB-C cable to pass-through the top part. I may end up trying to change the part where this connects to the table eventually because I can't move it very...

When replacing the original 80mm fan in the Rigol MSO5000 with a low noise Noctua NF-A9 fan, you will need a new holder to fit the bigger 90mm fan that has about the same air flow as the built-in fan but is quite a bit less noisy.I printed the holder...

I created this design specifically for the Kolink Rocket mini-ITX pc case with a 92mm Noctua fan on top of the LH-L9a-AM4 cooler and an ASUS ROG STRIX B450-I board. However, it should also fit well on other boards. To adapt this shroud to different...

It should just fit through pressure, no mounting hardware or tape needed. I made it for the "Kolink Rocket" mini-ITX pc case with the 92mm Noctua fan on the LH-L9a-AM4 cooler on an ASUS ROG STRIX B450-I board. Should fit other boards fine well,...

The GME diamond hands fan for the Fan Showdown

... decided to design one from scratch. This project should be a breeze to complete. To secure the fan in place, I can attach it with the rubber gaskets that came with the new fan unit.\nPrint Settings\nRafts: \n None Needed\n \n Supports: \n Optional

Humans now harness a dual-cooling system that simultaneously cools both the extruder and printable area using a powerful 30mm fan.

... the noise and provide ample airflow for my projects. If you're okay with less airflow, go with the 4010 model, but if high performance is a must, opt for the 5015 version. ... Note: Fan openings are built to accommodate inserts for added durability.

... cables neatly. The new fan provides better cooling, blowing 20m3/h compared to the usual 50x50mm fan's 9m3/h. For more information on the Noctua NF-A6x25 FLX, visit noctua.at/en/nf-a6x25-flx/specification. ... (Pictures taken during installation)

This is a complete version All-in-One fan duct and hotend for Argento-v6 hotend. It's directly inspired by http://www.thingiverse.com/thing:1292038, combining ideas from http://www.thingiverse.com/thing:1384844. There are two unique models available....

I wanted to customize the Noctua NH-U12S for my new PC because it's oversized and doesn't match the case and components colors. I created a cover similar to the one sold by Noctua for 20€. Since I didn't want to wait or pay 20€, I made one myself.

Fan Duct for 3D Upfitters Acrylic Case 12/8/20 Designed by JWizard Thank you for choosing JWizard’s 3D Models and Designs! The fan duct with my case broke 3 times already! I kept repairing it and gluing it back together. I got tired of doing that....

The part was created in the style of this part https://www.printables.com/de/model/275058-atomstack-m100-noctua-mod but the present version can be printed without any supports For finishing you will need the following things: 1.) the four printed...

... duct. ...No more sounds and enough airflow for my needs!!! Use 4010 if you don´t need or use high airflow for your prints if you need more airflow performance please use 5015 version Note: Fan holes are designed to use inserts for better durability.

NH - CR 9070 Combine Harvester

NH - CR 9070 Combine Harvester

In combination with a 40mm Noctua fan (with this shroud: https://www.thingiverse.com/thing:2076234), the printer is nearly silent. The only sound now is the stepper motors, which is greatly reduced by these feet:...

This part is an adapter for using a silent Noctua 60mm fan for cooling the Atomstack M100 laser-module.The part was created in the style of https://www.printables.com/de/model/275058-atomstack-m100-noctua-modbut the present version can be printed...

Two-in-One Fan Duct Remis for Hotend AiO Evo. Remix inspired by https://www.thingiverse.com/thing:839620. Learn more about the Hotend Aio_Evo at http://www.hotends.fr. ... Thanks to Accromeca for the photos.

Two in one Fan Duct Remis for Hotend AiO Evo. Remix available at https://www.thingiverse.com/thing:839620. Visit the website hotends.fr to learn more about the Hotend AiO Evo. ... Thanks goes out to Accromeca for their photos.

Fan Duct System Designed Specifically for ZONESTAR Series of 3D Printers, Including the P802Q, P802N, and Models Z5, Z8, Z9, and Z10.

Back in 2013, I required specifications for constructing a compact heat exchanger. ...The current NH-U9 and NF-B9 models apparently share the same dimensions.

I converted the "Improved Fan Duct for Anycubic Vyper" parts from Inches to Millimeters for easy import/slicing, and mirrored the "right" duct so it faces the correct direction.

Edited fan body version to use with CR touch mounting bracket because extra clearance is needed. ... Not tested yet. Use original printing settings as noted in original Fang Fan Duct for Ender 3 v2 by MakerSmitty

Made an adapter for NH-AAS in case you want to make a floor fan. Fits standard camera screw. ... MajorHardware version https://www.thingiverse.com/thing:4911660 Jadert version https://www.thingiverse.com/thing:4912018