fan duct for noctua nh d15 in combination w tall memory modules 3d models

When replacing the original 80mm fan in the Rigol MSO5000 with a low noise Noctua NF-A9 fan, you will need a new holder to fit the bigger 90mm fan that has about the same air flow as the built-in fan but is quite a bit less noisy.I printed the holder...

I created this design specifically for the Kolink Rocket mini-ITX pc case with a 92mm Noctua fan on top of the LH-L9a-AM4 cooler and an ASUS ROG STRIX B450-I board. However, it should also fit well on other boards. To adapt this shroud to different...

It should just fit through pressure, no mounting hardware or tape needed. I made it for the "Kolink Rocket" mini-ITX pc case with the 92mm Noctua fan on the LH-L9a-AM4 cooler on an ASUS ROG STRIX B450-I board. Should fit other boards fine well,...

The GME diamond hands fan for the Fan Showdown

... decided to design one from scratch. This project should be a breeze to complete. To secure the fan in place, I can attach it with the rubber gaskets that came with the new fan unit.\nPrint Settings\nRafts: \n None Needed\n \n Supports: \n Optional

... cables neatly. The new fan provides better cooling, blowing 20m3/h compared to the usual 50x50mm fan's 9m3/h. For more information on the Noctua NF-A6x25 FLX, visit noctua.at/en/nf-a6x25-flx/specification. ... (Pictures taken during installation)

I wanted to customize the Noctua NH-U12S for my new PC because it's oversized and doesn't match the case and components colors. I created a cover similar to the one sold by Noctua for 20€. Since I didn't want to wait or pay 20€, I made one myself.

... duct. ...No more sounds and enough airflow for my needs!!! Use 4010 if you don´t need or use high airflow for your prints if you need more airflow performance please use 5015 version Note: Fan holes are designed to use inserts for better durability.

I'm designing a custom fan setup using silent 4010/5015 fans with ducts. This will eliminate the noise and provide ample airflow for my projects. If you're okay with less airflow, go with the 4010 model, but if high performance is a must, opt for the...

This is a complete version All-in-One fan duct and hotend for Argento-v6 hotend. It's directly inspired by http://www.thingiverse.com/thing:1292038, combining ideas from http://www.thingiverse.com/thing:1384844. There are two unique models available....

In combination with a 40mm Noctua fan (with this shroud: https://www.thingiverse.com/thing:2076234), the printer is nearly silent. The only sound now is the stepper motors, which is greatly reduced by these feet:...

Two in one Fan Duct Remis for Hotend AiO Evo. Remix available at https://www.thingiverse.com/thing:839620. Visit the website hotends.fr to learn more about the Hotend AiO Evo. ... Thanks goes out to Accromeca for their photos.

Two-in-One Fan Duct Remis for Hotend AiO Evo. Remix inspired by https://www.thingiverse.com/thing:839620. Learn more about the Hotend Aio_Evo at http://www.hotends.fr. ... Thanks to Accromeca for the photos.

I converted the "Improved Fan Duct for Anycubic Vyper" parts from Inches to Millimeters for easy import/slicing, and mirrored the "right" duct so it faces the correct direction.

The part was created in the style of this part https://www.printables.com/de/model/275058-atomstack-m100-noctua-mod but the present version can be printed without any supports For finishing you will need the following things: 1.) the four printed...

Edited fan body version to use with CR touch mounting bracket because extra clearance is needed. ... Not tested yet. Use original printing settings as noted in original Fang Fan Duct for Ender 3 v2 by MakerSmitty

Made an adapter for NH-AAS in case you want to make a floor fan. Fits standard camera screw. ... MajorHardware version https://www.thingiverse.com/thing:4911660 Jadert version https://www.thingiverse.com/thing:4912018

Here's a remix of DWONH's fan duct, specifically designed for those who need a bit more breathing room between their fan and hotend. To achieve this, I've increased the distance between the two fan ducts from 32mm to 40mm, providing a safe and stable...

This part is an adapter for using a silent Noctua 60mm fan for cooling the Atomstack M100 laser-module.The part was created in the style of https://www.printables.com/de/model/275058-atomstack-m100-noctua-modbut the present version can be printed...

I've been using a single fan duct to cool my printing material for over a year now, and it's generally done the job decently well. However, I've found that there are specific models where its performance is severely limited, and no amount of...

Fan mount for facilitating Noctua 40mm hotend and filament cooler using two fans.

A custom fan design is needed to pair with the Hypercube Evo and PrecisionPiezo sensor, featuring a half-toroidal blower fan in the correct size for proper use. Additionally, a matching full-toroidal blower fan of the same dimensions as the original...

I recently bought 2 Noctua A4x20 fans and attached them to a fan duct. However, I didn't like the brown in contrast to the black of the duct. So I designed a cover for the fans and they fit perfectly on the 3rd attempt. They can be easily clipped...

Prototype version - MeanWell Cover for Noctua 60x25 fan. ...I built it once, it worked.

... Although designed for a VGA fan, 40mm fans from the ProStruder package were easily installed using small zip ties with no issues. ... Photos are not available as these fans are already humming away inside the printer, securely bolted in place.

Back in 2013, I required specifications for constructing a compact heat exchanger. ...The current NH-U9 and NF-B9 models apparently share the same dimensions.

Fan cover with a small recess for installing a filter. ...Designed for Noctua NF-A4x10 FLX, using the hardware included with the fan. ... Originally modeled in SOLIDWORKS, .stp available upon request

This comprehensive assembly offers an all-in-one solution or allows users to print individual parts, eliminating the need for supports and subsequent welding. ...For those interested in customizing the design, it has been created using Openscad...

I did a remix of thmjpr's version of the NH-AAS Deskfan. ...Only the MMS/Gopro mount is inverted, the rest is like the original one. It fits 120mm PC fans. Also added a stand for 25mm thick fans (GoPro screw required).

Many of you might know that SB fans on certain asrock motherboards fail soon and start making awful noises, I was so sick that quite expensive board has such a shitty fan in it (and thermal pads as well) I wanted to upgrade it with Noctua 4x10 fan...