fan ducting 3d models
114649 3d models found related to fan ducting.thingiverse
A MOD FOR THE CREATE AND PRINT V3 3D PRINTER 40MM 24V FAN DUCTING AND EXTRUDER COVER Print Settings Printer: V3 Rafts: No Supports: No Infill: 15% Notes: Print with fan face down placed right on build plat there should be no overhangs on either part.
thingiverse
A quick prototype for a tiny fan (square 15mmx15mmx4mm) housing to duct to round tube fitting.
myminifactory
Fan duct for 40mm fan for cooling 3D print. ... Printed it without support, 0.2mm layers.
thingiverse
This is an **experimental fan duct**. ... - No particular use case - Suitable for 3D printing
thingiverse
Custom fan duct for my Creality CR-5 PRO H. Four side air blow. Litle upgrate holder for fan. ...
thingiverse
Fan Duct pour Ventilateur de 40mm Hauteur de couche : 0.2 Épaisseur Parois : 1.2mm Remplissage : 25% Filament : PLA
thingiverse
Fan duct for Heacent 3D Printer 3DP02 Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter
thingiverse
Fan duct fore your hot end, 50mm fan, plus 360* part cooling! The mounting hols are m5 end 25mm center to center. ... Total higt is 80mm.
thingiverse
f you use this fan duct & think it makes your prints look better designed in such way, that the air blows just below the tip of the nozzle.
thingiverse
Fan duct for: https://www.thingiverse.com/thing:2828997 Update 18.03.2018: - Some minor changes to improve the airflow and stability Update 20.03.2018: - Extend the height, so the fan duct will fit in the radial cooler. ... Update 05.04.2018: -...
thingiverse
A fan duct for a UN3F 5015S squirrel fan I got to cool my prints. It snaps on without any screws. ...Installing the fan with this on definitely improved the quality of my overhangs.
thingiverse
This is a Fan Duct that I made to improve the cooling on my Geeetech A10 pro; it uses a 40mm fan I bought off Amazon. ... No need for infill or supports
thingiverse
I recommend using the "fan_duct_v6.1.stl" file and create only the support that touching building plane. The file have to be print in the towards that I have published it. ... Link for its fan holder: https://www.thingiverse.com/thing:3095442 Link for...
cults3d
I modeled this fan duct for the Anycubic Linear Plus to try to reduce the power supply fan noise. It helps a bit, mostly by changing the noise to a lower frequency, less annoying sound. I think it also looks pretty cool, like a big Cummins diesel...
thingiverse
I modeled this fan duct for the Anycubic Linear Plus to try to reduce the power supply fan noise. It helps a bit, mostly by changing the noise to a lower frequency, less annoying sound. I think it also looks pretty cool, like a big Cummins diesel...
thingiverse
Sorry for my bad English. ...My hotend was overheating and the heat was getting to peek, it was the abs melting inside peek and disturbing my impression. I drew this fan duct coolers for 40mm. ...I used zip tie to hold the peek
thingiverse
This is a fan duct that I designed for my ADIMLab Gantry-S. Its been working fine for me, I did cut out a few pieces so that wires could go where they need but that was something that I was expecting to happen. ... Happy Printing, ...
cults3d
Sorry for my bad English. ...My hotend was overheating and the heat was getting to peek, it was the abs melting inside peek and disturbing my impression. I drew this fan duct coolers for 40mm. ...I used zip tie to hold the peek