fan extender 3d models

This is an updated remix of the Ender 3 Pro Case Extended Remix, available on Thingiverse at https://www.thingiverse.com/thing:4107156. ... To improve airflow and cooling for longer prints, I've integrated a 60mm fan above the main board on the right...

This remix is based on the blank fan mount and has been lengthened by about 10mm to make space for a switch slot and cool the aluminum direct drive assembly of the extruder. Behind the switch, I've connected a tiny basic circuit with a diode to...

I've taken part of https://www.thingiverse.com/thing:4107156 and created a remix featuring the STEP file shared by @drewzh for the Ender 3 pro case, adapted specifically for the Raspberry Pi 4 with dual fan setup. ...A dual fan option previously...

Remix of part of https://www.thingiverse.com/thing:4107156 As @drewzh kindly shared the STEP file for the Ender 3 pro case, I have created a version for the Raspberry Pi 4 with dual Fan setup. There was a dual fan option available, but only for the...

New hotend from Creality sticks down farther than the existing one, so I made this up to at least get it close. Made for my Ender 3 Max but I believe it should be compatible with any Creality printer with a 4010. Post your makes on different printers...

The design perfectly fit snugly over the opening due to its sleek and streamlined dimensions, complemented by its wider side panels.

Easier to print and refined design.

I required an extra half inch of clearance for cables and accessories, so I added some spacers.

This is an extended version of ender 3 v2 stock hot end cooler fan duct. Default bolts can be used. Two snap fits pending to be added to the model as available in the stock duct. ...Yet, I was able to replace the original duct and I am currently using...

It also has extended legs to give the needed height to allow airflow for the fan. I put two sets of screw holes in the design, one set is counterbored to make sure short screws can reach, and the other set are not, making the screw hole stronger but...

... fan to any Lulzbot TAZ before version 5. ...Designed as a nozzle fan for e3D v6 or hexagon hot ends, this fan housing has movable areas that allow for vertical adjustment without requiring the use of heat-set insert nuts for mounting with m3 screws.

Modified version of the 'Semi-Circular Anet A8 Fan Duct' https://www.thingiverse.com/thing:1954001 I have installed a new feeding tube which offset my nozzle to a lower point relative the original one and I have also installed an auto leveling probe...

... located here: https://www.thingiverse.com/thing:1911146. Since this adjustment requires a fan duct that fits these changes, I designed this one. Images show the length and height from the fan mount to the center of the fan duct's circular path.

This optimized duct maximizes air flow and compensates for the additional distance between fan and nozzle due to the autolevel sensor support found here: http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct might collide...

This duct is optimized to maximize airflow while compensating for the additional space between fan and nozzle caused by this auto-level sensor support:http://www.thingiverse.com/thing:1911146 Without this sensor support, the duct may collide with...

I added the micro SD extension to give myself a spot for it. Now I can keep everything organized. ...I set it up vertically, making sure the curved side faces upwards.

<p>Added 4mm height the vertical ducto to lower the circle to get it rightly positioned when the hot end is mounted properly. ...The original places the circle around the heater block which just causes temperature fluctuation.</p> Category: 3D Printer...

I adjusted the vertical duct's length by 4 millimeters, realigning the circle for optimal placement once the hot end is securely mounted. ...The original setup positions the circle directly above the heater block, resulting in unwanted temperature...

This is the same as a https://www.thingiverse.com/thing:4894914, but the box has been moved forward to make room for bigger ESCs.

This straightforward modification extends the original design while also adjusting the slope of the wedge inside to optimize air flow across the tip more effectively. ...I have utilized this upgraded model on my machine for the past three months and it...

If you download please press ‘like’ to push this thing up the search to help others to find it. Add 13mm tall for in the case. ...

... The rest is pretty the same as my previous version: http://www.thingiverse.com/thing:1788901 I used two ultra bright leds and connected them with a resistor to the power connection of the fan. The resistor can be fixed at the top of the fan duct.

After creating my first Geeetech Prusa I3 Pro B fan duct, I thought it could definitely be improved. So, I created a version with two LEDs. The rest is pretty much the same as my previous version: http://www.thingiverse.com/thing:1788901. I used two...

This is a remix of the dual-fan nozzle cooler for Original Prusa i3 mk3S by ANTALIFE, which itself is a remix of the original by RosyRL. I've used the original for some time now. During that time, I discovered ANTALIFE's "reinforced" remix and truly...

This is a remix of the dual-fan nozzle cooler for Original Prusa i3 mk3S by ANTALIFE (which is itself a remix of the original by RosyRL) . I've used the original for a while. While looking to replace it I discovered ANTALIFE's "reinforced" remix and...

This is a Modified part for the Qidi X-Plus printer, To accommodate the changes that occur when you upgrade to the ***Extended*** Micro-Swiss MK10 All-Metal Hot-End kit. This is specifically for the Kit which uses a 22.35mm Thermal Tube, Not the...

Extended extruder knob long enough for Micro Swiss Direct Drive and 20 mm fan

I wanted better cooling for hot end so stretched shroud to allow for 4020 fan. ...Also, rounded out the edges of the blower shrouds to allow for better visibilty of what is on the bed while o\printing.

extended replacement feet for NR200, which allow bottomed mounted 120mm x 25mm fans. ...Fans will have about 8mm clearance to the ground

... these squash ball feet: https://www.thingiverse.com/thing:4335612 -Moved Raspberry Pi 4 down 7mm for a better fit with the original Pi PSU. -Increased size of opening for Pi PSU on side of case. -Added an additional fan mount for dual fans.