fastcap 3d models

Simple nozzles which fits the glubot fastcap.Two sizes available now, thick and thin!PETG, 100% infill, you need supports

Simple nozzles which fits the glubot fastcap.Two sizes available now, thick and thin!PETG, 100% infill, you need supports

Replacement part for Fastcap Auto-Lock Write-On Measuring Tapes.

Gridfinity Fastcap Long nosed marker holder. ...Marker: https://www.amazon.com/dp/B002NQPEE6

I have a FastCap 3rd Hand (a pole that extends and can hold things up, etc) and the foot portion of it broke, so instead of jumping through all the customer service hurdles, I decided to just print a replacement. It actually works even better than...

... slip pad 1 ring for carabiner or lanyard Please test your fitting and use food safe filaments I recommend 99.9% and TPU for the ring and the endcap. ...The fastcap part ideally printed at the highest quality with normal scale from PLA or PET-G.

I had a problem with my Glubot because the glue I use is extremely viscous. It took some time to force out the glue when the bottle was half or more depleted. So, I engineered a stand that guarantees the glue is always at the optimal level. It's...

I had a problem with my Glubot because the glue I use is very thick. It took some time to squeeze out the glue when the bottle was half or more empty. So I designed a stand that makes sure the glue is always at the proper level and ready to use.  ...

Attach a fastener to the holder of the 16oz GLUBOT bottle from FASTCAP. ...This requires a flathead screwdriver to securely mount it on your workbench, wall or any other stable surface.

Replacement cap for CA Glue bottle. ...Print the top with supports, they pop right out. The Cap does not need supports. Fits Starbond, Fastcap, Titebond, and other CA Glue bottles.

Use in drill. Not my design, remixed from FastCap design.The idea is to make smooth cuts into the Kaizen foam with the sharp end of this print. You might need to sand the end thin to sharpen. I haven't printed yet but would imagine it would work will...

This is a dedicated cradle for the FastCap FatBoy Pencil. Engineered to be attached securely using double-sided tape, hot glue - my go-to choice - or by drilling small holes and utilizing screws. To drill holes effectively, ensure a solid infill of...

This is a convenient wall mount for Fastcap measuring tape reels that come equipped with a belt clip on the back. It will likely fit any measuring tape featuring this type of attachment. You can assemble this in approximately ten minutes using...

... screws to be fixed in place and you can use glue to stick the damping rubber back to cover the screws. This is the selfie stick in question: https://www.bhphotovideo.com/c/product/924977-REG/fastcap_tech_i_stealth_ipole_stealth_23_5_53.html

... holder https://www.thingiverse.com/thing:3803129 I then decided why not make a slot to hold the actual glue to the activator can also so I made this. ... This is specifically for 2P-10 2.25oz glue bottles and 12oz activator spray cans from fastcap

Here's a wall mount holder designed specifically for the FastCap PSSR16 16 FastPad Standard Reverse Measuring Tape, but it also fits perfectly on the Harbor Freight Pittsburgh 16'x3/4 measuring tape and possibly other 16' measuring tapes. This...

This is a screw-it-in wall mount for Fastcap measuring tape reels that have the belt clip in the back. It'll probably work with any measuring tape that has a belt clip though!</p> <p>Put this together in about ten minutes in OpenSCAD... I've...

This is a custom holder for the Pica-Dry 3030 Longlife Automatic Pen and other similar pens, including Kaizen foam markers, fastcap pens, and kyoto foam markers. It uses six strong magnets measuring 10x2mm to securely attach to my toolbox. ... For...

Other items shown in the picture: * Fastcap Kaizen Knife * Craftsmen Plier Set * RJ 45 Tonor * Basic Punchdown Tool from Local Hardware Store * Milwaukee Compact Screwdriver * Westcott Scissors * Metal 200mm Digital Calipers * Plastic 150mm Digital...

It should work with all full-size FastCap tape measures and their derivatives. The backside of the holder's mounting surface is angled to more closely match the resting state of the clip. This was done to limit stress on the clip, hopefully...

This is my take on the Fastcap track saw guide rail wall mounted holder. Safely store your expensive yet bendable Festool / Makita track saw guide rails. These simple mounts can be wall mounted, ceiling mounted, mounted on a garage door, in your...

... not the DF700. You will need to glue the upper insert to the lid rib to keep the bits in place, I recommend FastCap SpeedTape. ...Print settings and filament shouldn't matter too much, I recommend using tree supports, 10-20% infill, and a brim.

... upright and attach the axle vertically without needing any additional support. A 56-piece pack of FastCap Traction Dots measuring 9/16 inches in diameter is recommended for use in the indents at the bottom of the holder, providing superior grip.

These components were designed specifically to work seamlessly with Festool/Tanos systainers, and I was actively pursuing a partnership with Fastcap to get them injection molded, but unfortunately, they backed out of the deal at the last minute. A...

Alternatively, Fastcap offers a variation of these holders that you can use instead. You can perform a Google search to see how they utilize them effectively. **Print Settings** * Printer Brand: FlashForge * Printer Model: FlashForge Creator Pro *...

This is my designed version of the Fastcap Rail holder. This has a a design where the cam is print in place. So no extra hardware is needed to set up the lock. This should fit most track saw rails. Kreg and Bosch will need some editing to make those...

Both are designed for a ~0.085" straw, which is the same size as the straw that comes with the 12 OZ Fastcap 2P-10 Activator can and roughly the same size as the 3 OZ WD-40 can's straw. The magnet is a 5 mm diameter sphere. I recommend buying a...

So I designed a two-piece version that is much more akin to the "inspiration" FastCap product that you can buy for $20+ per pair. Pretty self-explanatory. Print one base and one nut in the default STL orientations (flat for the nut and on the side...

So I designed a two-piece version that is much more akin to the "inspiration" FastCap product that you can buy for $20+ per pair.Pretty self-explanatory. Print one base and one nut in the default STL orientations (flat for the nut and on the side for...