feet for tcl tv 3d models
2307311 3d models found related to feet for tcl tv.thingiverse
Based on https://www.thingiverse.com/thing:4253124, however upon testing, these feet did not fit or work with my TCL 55S425, so I designed and printed some from scratch. Then I added a sound bar and made the extenders to allow for the remote to...
thingiverse
Simple holder for remote control of my TCL TV. You can use 2 screws to fix it to the wall. Works fine. ... Enjoy ;)
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5VGfBQzNZLc
thingiverse
Designed this for my TCL TV with a 10mm thick border. ONE LAYER contains bridging. ... .2mm
thingiverse
... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.
thingiverse
... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.
prusaprinters
I ended up making a mount out of some angle iron from Lowes that functioned similar to this piece.Do not use PLA for this or it will snap eventually.End of update__________________________________________Simple print. Use high infill. Requires two...
thingiverse
Mount Altec Lansing 5100 speakers to the foot mounts of a hanging TCL TV. ...Also includes simple cradles for the rear speakers.
prusaprinters
TV is a TCL 55" 4K HDR (2017) SB is a LG LASC47Printed in GST3D PLA+ 0.2mm layer height40% gyroid infill 4 perimeters6 top/bottom layers I (or you!) may consider printing this in ABS+ or PETG if it deforms over time but so far PLA+ has...
thingiverse
I have a TV and it was missing the feet or a base, which would require the TV to be mounted on the wall, so after much pondering i decided to use my 3d printer to make feet so it could stand on its own without a wall mount. These are not pretty, buy...
thingiverse
This is a feet for your tv of course... ...the stand well and I thought they came out pretty well so here you go.
thingiverse
In my case I use the TV's for side PC monitors and wanted to raise them to be level with my actual gaming monitor in the center of the two. By default, these are .625" high, but you can scale the model in your slicer to where you need them to be....
thingiverse
I designed this to hold my sound bar. ...If you look closely at the top of the tv, it has a slight forward slope. ...That and the curved back, required some accurate measurements and a few iterations.
thingiverse
We bought a Sonos Soundbar and it didn't fit under the tv so I made these feets
thingiverse
this is a shorter and simpler version of the 3DbyJB TCL ROKU tv leg. this will fit 40in and 43in TCL Roku tvs. ...
grabcad
TV support used to raise the TV in order to place the soundbar below and not interfere with communication with the remote control.3D printing support is difficult to remove. ...Minimum filling of 25% recommended
thingiverse
... ... Intended to be screwed or glued or double sided taped to something. I haven't printed it yet, but it should fit based on the source files and images. Edit: After printing, its a bit of a sloppy fit for my taste but it will serve it's purpose.
thingiverse
There are feet supplied with these TVs (MODEL NO.: E43V15B-AU) but I lost them so I prototyped my own. They work good! ... The screw holes (M4 35mm) differ from left to right hence two stl files.
thingiverse
There is one on the outside of the model that really no big deal (other than the obvious waste of filiment) but there is another one that builds in the back pocket where the TCL TV remote goes. These may have been my supports... not sure why one was...
thingiverse
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately)
prusaprinters
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately) Category: Replacement Parts
thingiverse
This mount allows you to set a TCL 43" 4K TV on its back for the purpose of using it as a digital gaming table to display maps. The height matches the bottom section of the TV so you only need two prints to hold the top corners for the TV to lay...
thingiverse
This is a replacement battery cover for a TCL Roku TV remote. There are several versions of Roku TV remote, so this may not fit yours. The STEP file was included in case you'd like to adjust it to fit yours. The Airtag cover is still not perfect....
thingiverse
A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.
thingiverse
A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.
thingiverse
This is a replacement battery cover for a Roku remote for TCL TVs. I made this because I hate searching for the remote, and I didn't want to buy a new one that does allow tracking. As a side benefit, the extra length makes it easier to grip the...
thingiverse
My sons TCL 43" Roku Tvs base legs were to short to fit his Xbox One and cable box under it so I designed 70mm tall ones and printed them on my Ender 3 Pro. ... These fit perfectly using the existing screws.