fidget switch 3d models

This is a remix of the original fidget toggle switch by kriswillcode. This version uses 4 8mm x 3mm or 5/16"x1/8" neodymium magnets to enable the switching action. This upgrade gives a much more satisfying and instant click between switch...

Update Feb 12, 2022: Added chamfered version to match the original switch better.This is a remix of the original fidget toggle switch by kriswillcode. This version uses 4 8mm x 3mm or 5/16"x1/8" neodymium magnets to enable the switching action.

... hold together with friction, but if not, a small amount of glue should suffice.If you printed a few switches and need a convenient holder, check out Liova's 3-switch box. nortmann_c also made an awesome keychain remix that's worth checking out.

Is an adaptation to which you incorporate a hole to be able to use it as a keychain. ...

Put a hole in kriswillcode's fidget toggle switch to be able to use it as a keychain.0,2 layer height15% infillno supports

Softer spring for the switch if you want to print it in 200% scale

Assembly manual:First print the spring of your choice (there are two versions, perfectly stiff and extra stiff.Note that the springs have bumps on one side of them, in this picture shown with a red line:         Then prepare your toggle switch and...

This is a compact remix version of kriswillcode's Fidget Toggle Switch. It is a little more than 25% smaller than the original, but uses the same mechanism. It has been changed in the following ways:The side view height of the main case is reduced...

This is a compact remix version of kriswillcode's Fidget Toggle Switch. It is a little more than 25% smaller than the original, but uses the same mechanism. It has been changed in the following ways:The side view height of the main case is reduced...

You can print the file one or 2 times depending on how large you want the hook to be. ...If you only print one, use the original case file for the other side.

I decided to add finger indents to make it not as slippery to hold in the hands.

This fidget toy is a tiny, clicky toggle switch! It's fully printable in about an hour and is only four pieces. ...You can change the "snap" effect by using either spring option and/or different materials.

This fidget toy is a tiny, clicky toggle switch! It's fully printable in about an hour and is only four pieces. You can change the "snap" effect by using one of the 3 spring options and/or different materials. **Don't forget to 'like'! If you make...

If the rotation feels stiff, use a file to trim it as necessary.Finally, set the spring and make sure the wheel is engaged, then attach the opposite side of the case.Note:I recommend that attempting to make a conversion from the original “Fidget...

This is a remix of Fidget Toggle SwitchThis toggle is like rocker light switch, there is 2 different toggles one is flat and the other one is slopeYou can reuse the spring from the original model, it also assemble like the original modelIf your...

Case and Spring parts are compatible with original “Fidget Clicking Wheel 2.0”.Print Settings:Material: PLA, PETGLayer height: 0.15 - 0.20mm  (For your information, I tested it at 0.30mm and it was quite tight due to the tolerance.)Supports:...

satisfying switch in a owl shaped case

This is a case for the Fidget Toggle Switch and is gridfinity compatible. Don't know why anyone would want this, but it exists. Printed fine in PLA at .3layer height, with 10% infill and no supports.  As featured on Voidstar Lab! ...Thanks Zack!

The original Fidget Toggle Switch by kriswillcode is very satisfying to use as well as being easy to print. But as soon as I saw it I wanted it to have one of those red safety covers, the sort of thing you see in movies when people are launching...

Add pause at 10.6mm for the spring, and another pause at 11.4mm for the toggle switch and the other case part.

Print SettingsNozzle Size: 0.4mmLayer Height: 0.2mmVertical Shells: 2Top/Bottom Layers: 4Infill: 15%Supports: Depends on how good your printer is at bridging.

<h3><strong>Print Settings</strong></h3><ul><li><strong>Nozzle Size</strong>: 0.4mm</li><li><strong>Layer Height</strong>: 0.2mm</li><li><strong>Vertical Shells</strong>: 2</li><li><strong>Top/Bottom Layers</strong>:...

Print-in-Place Fidget Toggle Switch for mmu3.Have fun!

Tactile, mechanical toggle switch for fidgeting - No extra parts needed! (Glue is recommended for the outer shell.) Printed using PETG but I'm sure other common plastics will work just as well. Also a great way to quietly annoy those around you...

Hey! ... I was on LoL loading time and bored, so I decided to get myself a fidget toy to relax! It is very easy and quick to print, no glue needed. No need for supports but I advise to put rafts for the small parts. Enjoy! ... NEKO2787

Not my idea...but my own design. Using 7 total 3mm x 6mm Magnets. ... My first full design of my own...about 6 hours total so far on this build.

<p>I swapped in part of one of his other wheels so that the rocker has more than 2 positions. I also made the rocker pointier and added a notched curve to the case. My goal was to make this a 0-5 indicator for a game, but I ended up going a different...

The original spring was too weak for me so i made a simple spring that can be inserted next to the springs to give them extra strength.Print two and just put them inside as seen on the photo

Again remix of: kriswillcodeGot inspired by th1nzz better gripJust found out there is already another middle piece which is wider by jbwebstHacked together with blender booleans and fixed broken stl by netfabb(through slic3r).This version is...