filament sensor 3d models

A Standard Bowden Tube for 1.75mm Filament, Optimized for Smooth Printing. Designed to Minimize Transitions by Eliminating the PTFE Tube Typically Found in Traditional Bowden Systems. Instead, the Print Head is Directly Connected to the Extruder via...

With my extruder 3mm lower was spot-on.Print SettingsPrinter Brand:Prusa Printer: Mk2.5sRafts: No Supports: NoResolution: 0.15 Infill: 20%Filament:Prusament PETG Black    Category: 3D...

This cradle allow to place the BigTreeTech Smartsensor on top of any printer, having a 20x20 top bar (here an modified Anet E10). ... It have not been tested yet (especialy the Marlin setup modification)

The original T-slot didn't fit snuggly, so I hacked these up in TinkerCad. ...I can't say whether the loose fit was a problem with the original design or my printer settings, but this version fits better for me.

This is a modification of the https://www.thingiverse.com/thing:4678852 I also added filets to all the corners to decrease stress points on the part You need one bracket and one bearing runner printed. ...

This is a modification of the https://www.thingiverse.com/thing:4678852 I removed the bearing post and changed it to a M8 hole. Use M8-1.25 x 1.25 or longer screw/bolt 4 to 6 washers to center the Type 608ZZ ball bearing. I also added...

I printed the original version for my ender 5 plus and due to the spool being hung offset on the wall, after prob 15-20 prints it Broke and snapped.I made one that mounts on both sides of the extruder making it very strong on all sides, also used...

I just turned the mount on this 90 degrees so that I could mount it on top of my Ender 3 for a top mounted spool and direct drive extruder.

Remix to remove mount bracket, allow mounting with double sided tape for printers such as the MPMD

Just a cover.

you will need some m3 brass inserts (link...

Remixed the design as I don't need the support for cable management. ...

Remix without the pulley.

You will need an M4x10mm heat-set insert, and an M4x15/16/17mm bolt.I thought about making a print-in-place mechanism but couldn't work out how to do it without support, so just did this instead. I think I may have lost some original parts while they...

Mounting the switch to the top of an enclosure requires a specific design that accommodates M3 hardware. ... This component is intended for mounting the switch assembly, which can be found at https://www.thingiverse.com/thing:2204729.

<p>For mounting the switch to the top of an enclosure. Designed to mount with m3 hardware.</p> <p>Used to mount this switch assembly. ...<a href="https://www.thingiverse.com/thing:2204729">https://www.thingiverse.com/thing:2204729</a></p> Category: 3D...

soporte para fijar el PFTE

I installed a precise opening for securely fastening a T-Slot Nut to a sturdy 2020 aluminum extrusion profile.

I forgot where I got the 2 models that I use to smash together to make this remix. ...Please pm me if it is your so I can give you the cred

Это переработка модели - https://www.thingiverse.com/thing:4488428. Не понравилось, что микро-переключатель не имеет крышки. Добавил крышку микро-переключателя, в связи с этим немного изменил крепежное ухо и стойку для крепления. Так же в...

Managed to figure out that the original was a bit of a struggle to secure onto the leadscrew nut, the holes weren't quite lining up properly. ...Ended up sketching out this design in no time at all.

The part needs an M6 thread for Bowden connection and a holder in the middle with an M6 fitting. Only the SWX1 version has the holder in the middle. ... To complete, you will need: - Two Pan Head Phillips Screws, M5 by 12mm - Three Flat Head Screws,...

斷料檢測器原本的位置距離擠出機較遠，因此無法發揮其應有的作用。為了提高生產安全，我將其移動至擠出機上方，現在更加安心了。如果您方便的話，歡迎來看看新的位置。感謝您的關注。

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Print vertically with support. ...Use PC4-M10 fitting for hotend for capricorne tubing and 3 Pin Tact Switch Micro Limit Switches Hinge Lever for Mill CNC KW4-3Z

I didn't find a design I was looking for, so I made my own!

the holes are to small but i drilled them up with 3,5 mm. ...

The printer I finally managed to get up and running had a few issues - the bowden stepper motor screw fixing was broken, and it didn't even come with a magnet.

Держатель датчика филамента для Anycubic Kobra Max Печать PLA

Neuer Halter für den Filamentsensor, der um 20° nach hinten verdreht ist und etwas nach oben geht. Mein Drucker steht in einem Ikea Platsa Korpus und wegen der Platzverhältnisse und der Filamentzufuhr oben durch eine der Verbindungslöcher war die...