filament spool 3d models

Filament spool

Filament Spool

filament spool

Filament Spool

Filament Spool 92mm(diameter)*63mm

Filament spool for a 3D printer

Filament Spool holder for your 3D printer. ...

Filament Spool for medium-small spool - uses supports

A 3D printer filament spool.Dimensions:- Outer Diameter: 200mm- Inner Diameter: 53mm- Thickness: 65mm

Just a filament spool. ... Need: screw - 4x m4 -12mm brass insert nut - 4x m4 - 8mm

Buildable filament spool. ... Coil diameter 200mm, outer width 72mm, inner width 64, inner diameter 84-90mm, hole diameter 53.

stand for filament spool You need: alu pipe 8 mm many bearings ABCE-9/608Z or lozysko.stl

filament spool for 1kg of 1.75mm filament. has 3mm wide gaps all round spool to see amount of filament of spool. ... also 8, 3mm holes for attaching filament on each side, totaling 16 holes.

A filament spool! That you can print. The spool is 20cm in diameter. ... It should work fine with both 3mm and 1.75mm filament.

Hi ! ...it's filament spool is work-in-progress. Files, instructions might change ! ... size in cm : Length 18.73 cm Width 14 cm Height 12.75 cm

... &nbsp;It's just a filament spool without all the bells and whistles of a MasterSpool and consumes less material. But be careful with it. ...It isn't as robust as a MasterSpool.</p><p><strong>You print and use this at your own risk!!!!!!</strong></p>

This is a small decorative filament spool I modeled. It comes in three parts to make it easily printable   Printing instructions: Print all parts with no support or adhesion and assemble. ...You might need to flip the "top" part over. 

A filament spool! That you can print. The spool is 20cm in diameter. It should work fine with both 3mm and 1.75mm filament. Instructions Print out the two parts, pop them together, and spool some filament on to it. ... Thats all you need to do.

A filament spool for PLA or ABS plastic. Instructions The material I used for the spool was 1/8-inch hard board from The Home Depot. Laser cut the spool sides and slats and then glue together with wood glue. ...If you want the use thicker material then...

I made this filament spool so that you could put more than one color on one spool. Supposed to work well with a lot of colors but small amounts of filament. You'll need superglue to put the pieces together. ...It would be better if someone made it so it...

Filament spool. Did personal use. Well suited for plastic in coils. printed with nozzle 0.8, layer 0.3. To increase the resolution, you can use a smaller nozzle diameter. Filling from 20% External diameter 200mm. ...The outer diameter of the spool...

This filament spool holder is designed for the small and large holes in spools. I used the standard filament holder for the ender3v2 but mounted a bar. The spring on the back is to add pressure to the spool so it won't unwind with the first...

Hey there, This is an easy and quick to print filament spool for a 608 bearing. (Rollerblade) It is made for 1,75mm Filament. Print the single side and one of the assemblys than glue it together. There is also an adapter to use a drill to rollup the...

For those with not that big printer surfaces (mine is 15cm x 15cm x 22cm), I made this filament spool, with the intention also to add some anti-slip tips at the bottom. I found some online with a plane base on the sides, but those didn't work for my...

I made a filament spool, size is about the same you'd get Creality filament on. It should take you about 4 hrs with 1 mm extruder. I made it with both PLA and ABS, worked out fine, just need to change the temperature. You will need to hot glue...

Make your empty filament spool reusable! You can take your empty inland spool and reuse it with spool less filament to save some money without having to buy the inland reusable spool. Instructions 1) Cut the side of the spool off. You will need to...

Filament spool, can be printed on any printer. It is important to properly prepare the support inside. Before printing, check the size of the filament to be worn. It may be necessary to reduce the size along the Z axis by scaling. Assembly...

This is my design for a filament spool, for people who, like me, make their own 3D printing filament. Two STL files are included, one for the sides (need to print two) and one for the middle bit. The middle bit has pads at one end to...

It has an outside diameter of 180 mm and a width of 20, 30, 40, or 60 mm so it fits normal filament spool holders or saves space as necessary, and the outer edge is fixed so edge-riding holders will work as well. The "Screw" end is compatible with...

This is a CNC-able filament spool for holding loose rolls of 3D printer filament. By cutting more of the wooden washers, it can be made wider. We cut this one in 18mm MDF and use it to hold Diamond Age Solutions Ltd. http://diamondage.co.nz 100m x...