film spool 3d models
72229 3d models found related to film spool.thingiverse
Film spool of my agat 18k is broken so i made this. ...It may work on another type of cameras that use film spool but i didn't tried it.
myminifactory
A 35mm film spool used in a Taxona camera. ...Might fit some other 35mm cameras, but I have not tried.
thingiverse
620 film spool Instructions Spool for use in respooling 120 film for 620 cameras. Suitable for SLS printing. See the two-piece spool by ComradeQuiche for a MakerBot-compatible version. The photo shows a standard 120 roll, a 120 roll re-spooled on a...
thingiverse
This is a usable 8 mm film spool. Print the two parts and snap them aligning the three cylinders located near the center of the spool. Use glue to make sure it doesn't separate when turning. ... Print Settings Printer Brand: ...
thingiverse
This is a module for openSCAD that creates films spools with a varying amount of sockets. It was inspired by mlagana's spool but completely redone. Instructions The included STL has 8 sprockets but using the scad module spool() with a parameter will...
thingiverse
... Still, you need a spool to wind the film on. If you don't have old spools (or the slightly-too-wide plastic spools made by Efke jam in your baby Rolleiflex), this 3d model might help you. This is the first 3d model I ever made. Not tested yet.
thingiverse
Instructions This is a basic spool for 120 film. This should be fully usable, and you should be able to use it to wind film onto. Measurements were taken from an existing 120 film roller, so I believe everything should be within specification. The...
thingiverse
## Spool for 120 film type **No support required** **No glue required** All the spools I found were either unprintable or unusable so I decided to design my own I made an interlocking cube 0.2mm smaller than the corresponding hole, so that the two...
thingiverse
Instructions 10 Print 20 Clean out support in drive opening at ends 30 Glue with super glue 40 Shoot some awesome photos 50 Get a new spool from the roll of film you shot 60 Goto 40 I've gone as far as printing this and gluing it together, but I...
thingiverse
... two halves together, use a few drops of glue to secure them if you like. The ends of the spool are quite thin, so depending on your print material, it might be recommendable to use black spray paint on the finished spool to make it more light proof.
thingiverse
This is an film spool adapter to use 120 film in cameras that originally took 116 or 616 type film. Note: this does not mean that the "red window" numbers will line up, just that you will be able to load 120 sized spools into the camera. There are a...
thingiverse
... anyway to be sure. Note it was a bit tighter on some Ilford brand film spools so could require just touch more sanding down on the edges and verticies of the tongue piece. ...Has been tested and confirmed working with Ilford and Kodak brand spools.
thingiverse
Edit it online https://tinkercad.com/things/eI7V5b96I1M Instructions Six film spools for use in respooling 120 film for 620 cameras. Carefully cut the spools from the sprue - nail clippers work for that. Suitable for SLS printing. For a...
thingiverse
Then I inserted the '+' on the other end into the film spool, inserted the other adapter/spacer into the other end of the film spool, and while pulling the circular pin out and away from the body of the camera, I slid the other end of the film spool...
prusaprinters
... ...Can also be used to transfer film from one spool to another faster than my Eumig 502. ...But be careful not to tear the film! Connect the tool in you reel, get your electric screwdriver or other fitting tool, and connect it like in my pictures.
thingiverse
I just split them into two pieces because I was having printing issues.
myminifactory
A 620 film spool for medium format cameras. 120 film spools are easy to come by, and can be bought new at camera stores, and online, but 620 spools are harder to find and can cost way to much for what they are.Though 120 and 620 spools are very very...
thingiverse
120 film spools are easy to come by, and can be bought new at camera stores, and online, but 620 spools are harder to find and can cost way to much for what they are. Though 120 and 620 spools are very very similar some older cameras just simply...
thingiverse
Created a simple Adapter for Azure Film Spool to be used on Sunslu Filament Dryer.
thingiverse
... would fit the original film. The original film was apparently ten frames of 14x14 mm pictures - with these spools I only get about 8 frames on them (that is, roughly 15 cm or so of film, with 22 cm or so of backing paper). ...Your mileage my vary.
thingiverse
The adapter has two parts, one that fits in the slot of the 120 spool and the cameras film winder, the other one is fits in the hole on the other side and is made to rotate freely in the camera. The fit is quite tight on some spools to make sure...
thingiverse
I made this adapter to shoot 120 roll film in a Kodak Brownie Target Six-16 (designed for 616 spool). By using 120 frame numbers 3, 6, 9, 12 & 15, I got 5 pictures. ... Examples : https://www.flickr.com/photos/danielb/albums/72177720299192748
thingiverse
Measurements taken from Kodak Portra 160 film cartridge
thingiverse
This is an adapter for a polaroid land camera to go from a 35mm film spindle to a 120 film roll. This allows you to use 120 roll film in a polaroid land camera with some other modifications. ...
myminifactory
I am in no way advertising for this brand of film, if fact i think it is a horrible film but I'm stuck with it and thats the way it is. This film causes endless troubles with the first layer beading up and turning into a little nest around the...
pinshape
Summary I am in no way advertising for this brand of film, if fact i think it is a horrible film but I'm stuck with it and thats the way it is. This film causes endless troubles with the first layer beading up and turning into a little nest around...
thingiverse
I am in no way advertising for this brand of film, if fact i think it is a horrible film but I'm stuck with it and thats the way it is. This film causes endless troubles with the first layer beading up and turning into a little nest around the...
thingiverse
I made this adapter to allow me to use 120 roll film in a Kodak Six-16 Brownie Junior Camera. ... In the Six-16 one set of 120 frame numbers line up, and if you use every second frame you get a 20mm overlap of frames.
thingiverse
I have downloaded a few 120 spools but find it difficult to print a perfect print due to the need for support, so I decided to design one to make it 3d printer friendly.
thingiverse
This is a remix so that they fit without any filing required. ... Tested to fit ib both Kodak and Fuji spools. ... No support required, it will bridge just fine.