filter for canon 50mm 1 8 3d models
2771480 3d models found related to filter for canon 50mm 1 8.thingiverse
This is a lens hood for the canon 50mm 1.8 ||. The original lens hood probably uses the thread on the lens. This lens hood is fitted to the lens using a screw on filter. Most people will have one to protect the lens. ...The thread of the filter fits...
thingiverse
This lens filter is for the Canon EF 50mm f/1.8 STM and creates a anamorphic like look. Please note that the filter is mounted with an UV filter on the lense. This work is based on the results of Josiah Vaughan. ... Installation instructions: ...
thingiverse
Lens hood for Canon EF 50mm f/1.8 STM, screws right on the mount. ... Only tested on crop sensor, might be in frame on full frame cameras.
thingiverse
... adds an amazing shaped bokeh, instead of your usual circle. Disclaimer : this item is not meant to take pictures of your mother in law. The kit goes was designed for a Canon EOS 50mm f/1.8 but should fit any lense with a 69mm diameter or lower.
thingiverse
This slips over the Canon 50mm 1.4 and has a half inch hole to modify the bokeh to have heart shaped bokeh. ...The walls and bottom are 1/4" thick.
thingiverse
... Camera. This filters could be used for film and photo both. And the Filter Holder, Case, and cover can be assembled when you carry it.(To prevent loss) I believe this is the best filter for Canon Crop body and 50mm 1.8 STM user. Thank you! ...
thingiverse
Print upright, no supports, 20% infil twist locks onto Canon EF 50mm 1.8 lens
thingiverse
Customized version of https://www.thingiverse.com/thing:1986103 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1986103
thingiverse
... cameras and telescopes, why not my binoculars too? ... This is a simple adapter that slips into the objective opening of Canon 10x30is binoculars and presents a cutout to receive a 2" filter, eg. ...some sort of light pollution or high-contrast filter.
thingiverse
This is a lens hood for Canon 50mm F1.8 EF STM. ... It can be screwed to the lens the other way around.
thingiverse
Clip-Filter para Canon EOS Para filtros de 1,25" O filtro tem que ser desmontado.
thingiverse
This is a remix of Manticorp's hood for the Canon 50mm f/1.8 STM lens. I used the original as the basis and redrew it in FreeCAD. *** Note that it is design for the new STM version. *** Having acquiring the lens, I don't want to pay the ridiculous...
thingiverse
I needed to remove dust from inside my Canon 50mm F1.8 STM lens. The front lens holder requires a custom tool for removing it without doing any damage to it. In some tutorials, others are using a flat screwdriver head or the metal caliper to open...
cults3d
Didn't feel like paying for a lenshood and wasn't sure if there was a different between the EF and RF 50mm F1.8 so I designed this one myself. Got a bit lazy with precision so I ended up printing this at 102% on the X and Y axis and 100% for the Z...
thingiverse
Didn't feel like paying for a lenshood and wasn't sure if there was a different between the EF and RF 50mm F1.8 so I designed this one myself. Got a bit lazy with precision so I ended up printing this at 102% on the X and Y axis and 100% for the Z...
thingiverse
This is an adapter to screw 1.25" filter or reducer to Clip on Canon DLSR Camera You must print it with superior quality, I used 0.1mm layer height You will not get good thread with 0.1 layer height Thanks, Enjoy! ... Print Settings Printer: ANET...
thingiverse
Customized version of http://www.thingiverse.com/thing:56910 Custom bayonet hard case for Canon 50mm f1.8 EF lens. Labeled or unlabelled top. Line with craft foam for full protection of lens. ...If using labeled top, print text side up and trust...
myminifactory
This lens hood is custom designed for Canon EF 50mm f1.8 STM lenses. https://youtu.be/irInNruz5Yc A lens hood attaches to the front of your lens and blocks stray light from causing flare in your photographs. It also helps protect the lens from...
thingiverse
This lens hood is custom designed for Canon EF 50mm f1.8 STM lenses. A lens hood attaches to the front of your lens and blocks stray light from causing flare in your photographs. It also helps protect the lens from damage if you bump into...
thingiverse
... conversion ring diameter 58mm for a 50mm lens. ... I use it on my 50mm f1.8 and I can switch between a 50mm and 58mm lens with the same filter. ...Printed with a 0.2 nozzle and a 0.12 layer height due to the size of the thread and it works perfectly.
thingiverse
The Canon 35mm RF lens for the EOSR / EOSRP has a clip lip on the edge of the lens that allows for a stand-off filter holder to be designed. My motivation was to hold 50mm Astronomy filters in front of the lens for long exposure astrophotography. ...
cults3d
Model of this charming cannon of the 2nd world war. ... If you have more ideas in making it more detailed, contact me! If you want me to print it for you, contact me: https://www.facebook.com/Infinity3D-279332426036783
thingiverse
GoPro Hero 8 mount with filter glass 50mm (removed from 52mm filter) for Martian frame https://youtu.be/GbgDKpVxycU
thingiverse
I made this clip filter to use the LPF filter (blue one) that I previously remove from my 750D. ...I use it when I'm not doing astrophotography to keep the original white balance.