filter for rokinon 14mm 3d models
2237589 3d models found related to filter for rokinon 14mm.thingiverse
I built this filter holder to use with my Rokinon 14mm ultra wide angle lens on my APSC cameras. Is buit in 5 parts. a semi cilinder that sorround the actual hood of the lens, to prevent reflection from behind in the filter, two actual filter guide...
thingiverse
##NEEDED: - PLA for filter holder - 4x M3 screws at least 20mm length with nuts - TPU for side catches - Original Samyang lens hood or Velcro. If you're using the original samyang lens hood like me, it's important that you 3d printer is...
thingiverse
This is a filter adaptor ring for the Rokinon/Samyang 14mm ultra wide angle lens. This adaptor allows you to use 95mm threaded filters like a circular polarizing filter, Neutral density filter, or other types of filters on this fixed hood lens. ...
thingiverse
The Rokinon 14mm is an excellent night photography lens, but like all lenses it can be difficult to achieve a good infinity focus in the dark. With these rings (you will need to print two of them) you can set infinity focus in the daylight, then...
thingiverse
To use filters with this adapter, one needs to remove the filter from the threaded ring and put it directly into the external body, and fix it in place with the inner body. Print both parts with ironing to increase precision of flat surfaces. ... ...
cults3d
... To use filters with this adapter, one needs to remove the filter from the threaded ring and put it directly into the external body, and fix it in place with the inner body. ... Print both parts with ironing to increase precision of flat surfaces.
thingiverse
... to share what I've started here. Ideally - print at high-ish settings to prevent shear layer separation. If you should print one, let me know!! I designed in Blender with curves... I've shared the Blend file for you to adjust if you want to remix.
thingiverse
Print in ABS, fits snug on the lens.
thingiverse
Simple mount for square filters (100*150mm) for the Samyang/Walimex/Rokinon 14mm f.2.8 lens. Settings: Resolution: 0.2 mm Infill: 15 % No supports needed Print with round side on the printbed. If fit on the lens is too tight, place the...
thingiverse
This is a Filter cap fitting on a 3/8 inch pipe (17.14mm), keeping rubble out of the pipe. Instructions I made this for my aquarium vacuum cleaner, to keep stones or snails from getting sucked. ...Please let me know what you do with it.
thingiverse
Archived Designed - May 2018 Adapter to mount Benro FH100 filter holder to the Olympus 7-14mm MFT lens. You must add a strip of thin felt tape around the inside edge to hold the adapter snug on the lens hood. My intention was to sell this at my...
thingiverse
Customized version of https://www.thingiverse.com/thing:2168672 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2168672
pinshape
Attempt at your own risk, I would definitely advise PLA because it's more natural and doesn't have the harsh chemicals of ABS but I seriously doubt that it would get hot enough for any chemicals to be released from the plastic. Print SettingsRafts: ...
thingiverse
Attempt at your own risk, I would definitely advise PLA because it's more natural and doesn't have the harsh chemicals of ABS but I seriously doubt that it would get hot enough for any chemicals to be released from the plastic. The most recent one I...
thingiverse
---------------------------- The Rokinon/Samyang 135mm f/2 is a great lens for astrophoto, but it does not come with a tripod collar. There are some people that use another lens' collar, I thought that solution a little poor. This solution is meant...
thingiverse
Rig to mount a stepper motor to a Rokinon 135mm (should be fine with the Samyang version too I'd think). Pretty basic setup. I use a Losmandy VUP7 dovetail. The screw holds are therefore made to explicitly work with that dovetail. There are 2...
thingiverse
This a filter holder for the Olympus 7-14mm pro lens. To use it print the hood, and adjust the fit by either scrapping inside or adding tape. I prefer it loose and use tape to hold it in place. Create a hinge between the 'mask' and 'shim' using...
thingiverse
The Panasonic Lumix 7-14mm f4 comes without a filter thread and fixed hood thanks to the bulging nature of the front element, so this is a simple way to fix a 100x100mm square ND filter onto it. There is ZERO vignetting at 7mm, but please let me know...
thingiverse
Eyepiece Container for Rokinon 114mm Reflector Telescope Eyepieces
cults3d
A filter holder for a samyang 14mm. 100x100mm filters. ...Do not work on Full Frame cameras
thingiverse
A finder scope holder for Rokinon 114mm reflector telescope in case you broke yours like I did.
thingiverse
A filter holder for a samyang 14mm. 100x100mm filters. ... Do not work on Full Frame cameras Download: https://cults3d.com/en/3d-model/home/lens-samyang-14mm-double-filter-holder
thingiverse
This is a focuser to be used with these components: https://www.thingiverse.com/thing:5140868 - Focuser box https://www.thingiverse.com/thing:4906949 - Collar for Rokinon 135mm lens for Fuji Use the focus frame according to your system. See pictures...
thingiverse
This is a two ring adaptor and dovetail plate for a Samyang/Rokinon 135mm F2 lens. The dovetail and rings are joined with M4 bolts and the lens is secured in the rings with two M6 nylon bolts, do not over-tighten the front (large ring) nylon bolt as...
thingiverse
A filter holder for a samyang 14mm. 100x100mm filters Designed for a friend, i dont know if it works! you will need 2 nuts and a 3mm bolt. ... CHECK OUT my portfolio and leave a like: https://www.behance.net/andreziio6a17 It would help a lot!
thingiverse
These parts basically adapt a manual focus Samyang/Rokinon 85mm f/1.4 manual focus lens for astrophotography on a motor driven mount with support for Electronic Auto Focus with a ZWO EAF motor. There is also a one-piece filter step ring for...
thingiverse
... in their CAD software. ...Just download the file, add it to your design and subtract it from the file to create the interior threads for your silencer. ...I have included 14mm positive and negative threads, but i am willing to add more if its useful.
thingiverse
This is a print in one bubbler that accepts a glass 14mm bowl. ...Printed in PETG at 0.15mm detail.
thingiverse
this is a Remix of the spiked Canopy The bottom is a little thicker so it doesnt wobble to much. also highered the Canopy around 5 mm to get the props out of view. ... Original Thing: https://www.thingiverse.com/thing:3385065