fireball xl5 models

Here is a rewritten version of the text that meets the requirements: We reduced the length of the front legs to match the frame perfectly. Convenient tool access is now available at the front, making installation a breeze. A speed hole has been...

can be print without support i used tpu you need a zip tie

This is a remix. Changed it so that it fits in front of the Nazgul V4 and V5. Fits every other 6mm standoff. Dimensions from hole to hole are 24.5mm. It also fits in the back if you squished the arms together. I found out after printing that the...

Replacement part for adding GPS to the Nazgul5 adapted for the Matek GPS M9N-5883

A compact 30-degree camera mount is utilized to stabilize the GoPro Session and Runcam HD cameras. The mount's versatile design allows for easy installation on various surfaces, providing a secure hold for both cameras. ...To further enhance stability,...

This is the base for the gimbal, you will also need the Universal Mount: https://www.thingiverse.com/thing:5135106 Guide for 3D printing the gimbal design here: https://medlindrone.com/2021/10/14/how-to-3d-print-fpv-gimbal/ More Info at...

A simple 30° support for camera. ...I use it with gopro session and runcam hd (add collar in the second hole for runcam) You can add foam pour a better absorbtion in case of crash :)

Hi, this Idea is based on the Flight Controller Dirt Protection from the Diatone Roma. I really like this, because I using Props-Out configs and dirt/grass in the Flight Controller/USB ports is really nasty. This clip may fit to any frame where the...

<p>Tried to make this as true to the original as possible. This fits a Nazgul5 v2 perfectly.</p><p>Print with no supports in the original orientation I have provided. For a full set, print two of the left and two of the right.</p><p>I highly suggest...

The top plate needs refining around the hexagon, specifically at the spot where it meets the rear section near the connector. A bit needs to be trimmed back to create a smooth fit. Printing supports on the adjacent side will help stabilize the...

Individuals typically measure and describe angles in degrees. A 25-degree angle is a moderate incline, while a 35-degree angle represents a more pronounced slope. ...Both angles are commonly encountered in various contexts.

Standing at a remarkable 28 millimeters tall and boasting an impressive 27 millimeter standoff spacing, this device proudly showcases its advanced design. ...Its compact yet powerful micro camera stands out with an impressive width of 19 millimeters,...

25mm spacing on standoffs. My battery might be a little bloated so it might be a little loose for a new buzzer. ... TPU with 100% infill and supports

The IFlight Xl Series Of Race Frames - A Delicate Balance Between Authenticity And Innovation. The Standoff Diameter Is Where These Frames Truly Shine, Offering A Distinct Advantage Over Their Counterparts. ...I Was Unable To Find A Suitable...

<p>can be print without support&nbsp;</p><p>i used tpu&nbsp;</p><p>you need a zip tie &nbsp;</p>

30 degrees mount for [RunCam Hybrid](https://www.banggood.com/custlink/KmvhVFyuQB) camera. This will need [2x M2x8 screws](https://www.banggood.com/custlink/mvmY5HhTqF) to hold camera in place. ... This has to be printed with TPU to prevent Jello...

This mount is essential, particularly when capturing wide-angle shots on an XL7 camera. ...It positions the lens far ahead, allowing key elements to remain out of frame!

Its flat on one side. ...I printed it with brim and support everywhere and it worked very well.

Replacement part for adding GPS to the Nazgul5 adapted for the Matek GPS M9N-5883 Category: R/C Vehicles

Remastered to a comfortable 25° angle. ...The previous 35° setting had been pushed way too far and didn't even reach the recommended 30° threshold.

I needed a custom mount for this frame immediately, so I decided to create one myself. Unfortunately, I don't remember where I obtained the top half of the design, but I carefully measured the top plate using calipers, designed the base from scratch,...

This is a remix. Changed it so that it fits in front of the Nazgul V4 and V5. Fits every other 6mm standoff. Dimensions from hole to hole are 24.5mm. It also fits in the back if you squished the arms together. I found out after printing that...

1.5mm shims for the cidora fpv camera. ...installed between the carbon plate and the fpv camera

An accurate lock-on.

Simple antenna mount for rear standoffs. Prints without supports. leaves 6mm of space in the slammed (lowrider) version for immortal T mount. ... Print in flexible material - this one was printed in Polipropylene.

GoPro mount for a carbon fiber FPV racing frame

This is the ultimate solution for your GoPro mounting needs. It seamlessly integrates with ReelSteady Go, ensuring a perfect fit every time. The level of customization is unparalleled, allowing you to adjust the number of ZipTies and softness by...

These are the parts for a easy no modification conversion to hobby grade parts for the radio shack 4x4 off roader. Uses an Traxxasxl5hv esc and traxxas servo motor. One Roll bar has a solid version of the lights on the roll bar. One...