first layer calibration 3d models

I'm excited to share with you a special keyring featuring my very first noozle. To make it extra safe, I designed rounded corners instead of sharp edges. This way, it's perfect for holding onto your treasured noozle without worrying about getting...

So I created a smaller one :)It is designed for my MK3s but you can easily skale it depending on your requirements.Because every area is connected it is simple to remoove and quickly start the next print.Before you start this calibration clean your...

Before you start this calibration clean your print bed and do a simple first layer calibration. V1 with circles (quite difficult to fill all gaps) and small paths in between. V2 Extra_Slim should be a little easier to print and has minimal...

This is a test of bed leveling in 3D printing, allowing users to assess whether their bed is properly aligned and if the first layer adheres accurately. As it prints, individuals can manually adjust the bed height to fine-tune its levelness.

Remix is Born - A Humorous Take on the Ultimate Baby Gift Inspired by the ingenious design of Dutchmogul's Mace, Remix brings a fresh twist to the world of square-shaped gifts. Measuring 100mm on each side, Remix makes for a rather imposing...

In 2009, Mathieu Glachant (syvwlch) posted the first thin-layer design on the Thingiverse, as well as several other firsts*. As he describes it, "This rests on the notion (or hope?) that if you print something sufficiently thin, it will bend without...

... corners up to 9mm thick. ... Additionally, I trimmed a small portion off the bottom of each piece because they didn't print well on the first layer (see attached screenshot). ... To successfully print these parts, you will require the use of supports.

A test model mainly indicate first layer quality for moderate printing time exposure, and subsequent effect. Directional indicator record the state of config long after test trail took place. ...As well as serve as an extra test work load.Place each...

I remixed the design from William_Additive so i can use it on the corners of glass tables (up to ~9mm thickness).I also cut a tiny bit off of the bottom of the original things, because i got no usable first layer with them (see attached slicer...

Since this is my "first" edition of this light it is of course on your own risk! I like it very much and will not miss it :) Have fun printin! Update 1 Clip 2.0: Clip fit good but wasn´t strong enough to give any support. I redesigned it...

Since this is my "first" edition of this light it is of course on your own risk! I like it very much and will not miss it :) Have fun printin! Update 1 Clip 2.0: Clip fit good but wasn´t strong enough to give any support. I redesigned it but the clip...

Testdruck, für die erste Schicht.50[mm]x50[mm]x0,2[mm]Druckeinstellungen:Material: PLADrucktemperatur: 200 °CDruckbetttemperatur: 60 °Cmax. ...Druckgeschwindigkeit: 80mm/s

I just wanted to summarize these together, so people can try different infills on square.

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Crafting a foundational element 60x60mm in size, measuring out at 0.2mm in depth

<p>I designed this to test my Ender 3 printer as I was seeing some strange marks in the prints. The shape was made to print in a single line and you can use it as a visual guide to see if your print bed is level. It also proved very good at showing...

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Customized version of https://www.thingiverse.com/thing:3519658 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3519658

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

if you want to test your bed leveling on flsun sr super racer.

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Ein simpler Testdruck für Sidewinder X1 v4 und gleich große Drucker. Druckfläche 250 x 250 mm plus circa 3mm Skirt Distanz Standard Durchmesser Düse: 0,4 mm Linienbreite 0,8 mm Höhe 1mm Dieser Druck dient zum nachjustieren der Druckplatte...

Ein simpler erste Schicht Test für den FLSUN Super Racer. Durchmesser der Testdruckspirale max circa 250 mm Skirt Distanz: 2,5 mm 2 Linien Standard Durchmesser Düse: 0,4 mm Linien Breite Testdruck: 0,8 mm Höhe : 1mm Cura Setting:...

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

This is just FunkyDiver's laptop with a quick fix to make it more reliably printable now. The original STL had the laptop base 0.2mm above the print surface compared to the laptop screen, which caused half of my prints not to adhere properly and left...

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

Customized version of https://www.thingiverse.com/thing:3519658 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3519658