first quadcopter build 3d models

375022 3d models found related to first quadcopter build.

Quadcopter 250
grabcad

I designed this quadcopter for a hs1177 camera and g9 servo for tilt (headtracking) (first quadcopter build)

First quadcopter
grabcad

Quadcopter designed for first steps into multirotor world. It has super-wide landing gear so you don't damage you propellers when landing not nicely. It also have strong aluminum arms for hard landings and crashes. ...The dome is 3D printed with...

BRONKS 650 Quadcopter Build
thingiverse

I was looking for something bigger than a 450 quadcopter so I could get more hover time and heavy lift. I settled on a 650 size to build. I plan to run these with a T-Motor MT4008-18. ... Still need to modify the upper and bottom plate.

x450 quadcopter build
grabcad

The CAD model of the quadcopter I built for my independent study. ...Specs: turnigy x450 carbon frame, turnigy d2822 motors, dji 10 " carbon props, multi wii se 2.5 flight controller, 2 x 5,200 mAh battery pack Li-poly, Q brain 4 x 25 A ESC, turnigy 9x...

First Build v2
thingiverse

I thought the addition of holes at the base of the build would be a good idea so that the cables could be easily squirrelled away Please if you've an idea how to improve this idea please comment thank you. This thing was made with Tinkercad....

CONTEST: first one to build...
youmagine

Print it twice.create a 3 sided pyramid with it.Post a picture of you printwork first.Win a design request by me! ...This means you can ask whatever you want (please not to artsy, I'm more of a techy), and keep it do able please.I will post the...

Frank26080115's first 3D printed quadcopter
youmagine

quadcopter, featuring folding arms, tucked away electronics, anti-vibration flight controller http://eleccelerator.com/my-first-3d-printed-quadcopter/

First Build
thingiverse

Customized version of https://www.thingiverse.com/thing:1672381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1672381

First build
thingiverse

Foxygirl2865: A lake with trees and mini flowers

Mini Quadcopter scratch build. Size 300
thingiverse

... at 65% throttle. Instructions Print motor mounts flat side to build plate, use some support if needed. Gps stand print top side down, use some hot glue to fix module in place. ... Fit carbon rods into blocks, then drill 3mm hole to fit a crews.

My first RC build and my first 3D model
grabcad

When I decided to build a quadcopter, I decided after a couple of decades of putting it off, and sticking to 2D CAD, to try and learn 3d modelling and build a virtual copter too... This is my first go... a few evening of watching YouTube video's and...

First Quadcopter Design
grabcad

In developing

3D PRINTABLE MODULAR QUADCOPTER (5040 PROPS) - 150MM BUILD PLATE
grabcad

THIS SOLIDWORKS ASSEMBLY CONTAINS A FULLY 3D PRINTABLE QUADCOPTER CHASSIS WHICH IS OPTIMIZED FOR:150MM BUILD PLATEQBRAIN 4x20 ESC5040 TRI-BLADE PROPELLERSNAZA CONTROLLER2000-2300KV MOTORS

(My First Upload) 5 Inch Racing Quadcopter Propeller
thingiverse

5 inch propeller designed for racing quadcopter. Comparable to DAL Cyclone 5050Cx3. STL file is large because my STL tolerences in SolidWorks are low. Might upload a 2-blade version upon request. Statically-tested on 2205 motors at max throttle. No...

my first build
thingiverse

Customized version of http://www.thingiverse.com/thing:279864 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options:...