fishing line spooler 3d models
165194 3d models found related to fishing line spooler.thingiverse
The fishing line spooler attached directly to your fishing rod to make spooling fishing line on spinning reel easy.
thingiverse
This fishing line spooler can be attached to nearly any fishing pole thanks to the adjustable clamp. ... When assembled it has an integrated line cutter and a slot cut into the spool disk to capture the line when spooling is complete.
thingiverse
line spooler for fishing poles... fishing line hub bolt is 5/16 carriage at 6 inch long and the mount bolts are 1/4 carriage at 2 inch long. the holes are designed to hold the square collar of the carriage bolts. add springs,washers and wing nut to...
thingiverse
Hello All, This is a remix for the line spooler created by Jeeprk (See link to original https://www.thingiverse.com/thing:5177521 I remixed the smaller portion of the clamp in order to use on smaller fishing poles for ice fishing. This was my very...
thingiverse
Tool to spool fishing line on a spinning reel using a power drill. Part 445 (44.5mm) is 1/3 of circle, print 3 times. Use and O-ring. Bolt center is threaded to accept 4mm rod for added strength to prevent crushing when using a power drill. ...Print...
pinshape
Summary Tool to spool fishing line on a spinning reel using a power drill. Part 445 (44.5mm) is 1/3 of circle, print 3 times. Use and O-ring. Bolt center is threaded to accept 4mm rod for added strength to prevent crushing when using a power drill.
thingiverse
Fixed the STL file for the Fishing Line Spooler
thingiverse
Simple tool for removing fishing line from the spool. You simply pinch the line between the two cones and wind up the line using a drill. Print two of these cones. Place a 5/16 thread nut on one of the cones. On the other cone use a 5/16 threaded...
cults3d
... spool sizes of filament to be changed in under 30 seconds. There is a socket on the end of the mandrel to accept a 1/4" drive which can be used with a cordless drill and an empty filament spool to quickly strip fishing lines on many fishing reels.
thingiverse
A cheap solution for putting new line to the fishingreel :) Printed at 30% infill There is two different versions the small one that i printed and a bigger one for up to 14 cm wide spools. for the small one you will need 1x m8 nut and bolt and 2x...
thingiverse
Fishing Reel Spooler. Made on both the Ender 5 Plus and the Ender 3 V2. ...
thingiverse
This is a guying/paracord line spooler. There are two versions: 7mm or 5mm thick. ...I printed this from PET-G wit 30% infill.
thingiverse
Simple fishing reel spooler that i came up with after needing to respool one of my fishing rods. ...Uses some hardware and a spring you'll need to source locally.
prusaprinters
Simple guying line spooler. I made it for my amateur radio station. You may also use it for kite or as a general paracord spooler. Print instructionsThin version is 5mm, thick is 7mm. ...I printed this from PET-G.</p>
thingiverse
Tired of twisted fishing line? Tried spooling with the pencil trick? Label side up? Label side down? Still having line twist? Give this gadget a try! Hardware: -22mm fidget spinner ball bearing -M3 x 20mm cap screw -Hair tie, elastic band, or...
thingiverse
... it in place Lock the device (the spooler? the re-spooler?) between the two M8 nuts per the instructions in the video and then run the drill anti-clockwise to spool your line. Easy peasy. ... It turns a five minute job into a thirty second job.
prusaprinters
<p>I created this design after looking around on <a href="https://www.amazon.com?linkCode=ll2&tag=thingiverse09-20&linkId=e4759bff1fa9a55a0f897d801ce2d765&language=en_US&ref_=as_li_ss_tl">Amazon</a> for something similar and after...
thingiverse
I created this design after looking around on Amazon for something similar and after scouring the internet for 3D printable solutions. ... I designed this in Fusion 360 and printed it on my heavily modified TrueUpLZ 3D printer.
grabcad
Spooler withpneumatic clamp, for unwinding rollsand feeding the metal sheet to the press.Unwinding speed is 11 rpm
thingiverse
New spooler in progress. I try to use only printed parts but in my design we need nuts, screws and bearings. Let me have the time to put a description and how to assemble the set. For the moment, I have put an assembly in STEP format which you...
thingiverse
I didn't like that the other spoolers on thingiverse did not let me choose the thickness of the rolling tube, i wanted a spiralised one so it would roll nicely without a seam. well i made one, based on a piece of Openscad code from flyte. ... You'll...
thingiverse
This holds the fishing line when you are respooling your fishing pole.
thingiverse
A fishing line holder used for spinning, uses an M4 nut and bolt to secure.
myminifactory
A fishing line holder used for spinning, uses an M4 nut and bolt to secure.