fishing rod rack clips 3d models
196438 3d models found related to fishing rod rack clips.thingiverse
A nice piece to hold a simple clips together or store 2 pieces of fishing rods. ...Okuma Dead ringer dr742ul is specially designed for serial number one fishing pole but it probably thinks it might be suitable for other rods as well.
thingiverse
A nice piece to hold a simple clips together or store 2 pieces of fishing rods. ...DAİWA PROCASTER GAME 2,2.70 is specially designed for serial number one fishing pole but it probably thinks it might be suitable for other rods as well.
thingiverse
Going to do some surf fishing, but didn't have a good way to hold the rod when it's collapsed. Made these clips that use an M5 Bolt and Nut to hold the two pieces together without getting the line tangled. ... It will probably work with most surf rods.
thingiverse
A handy thing to put your fishing rods against the ceiling. ... Printed in PLA 50% infill
thingiverse
This is a remix (a re-imagining actually) of the Fishing rod Clips by Sjefke. The main difference is that they're about twice as large while the holes are all mere 5mm in diameter, so a standard screw should fit nicely. Also, one side of the closed...
thingiverse
Tried some of the other clips from Thingiverse but all my rods had different dimensions so I designed these clips to be more or less universal. These are easy to modify. Just load them into Tinkercad and adjust them to suit. Print them in the...
thingiverse
This is my fishing rod rack. ...I wanted a rod rack to go on the ceiling here it is Instructions 25% infill is strong enough for rods.
thingiverse
In addition to transporting fishing rods on the Tesla, the Rear Fishing Rod Rack's two modular RodHolderWithM6HeatSetInserts may be used with the two LockRings, two FemaleBayonetConnectors and the CaddyBaseShortBidirect to mount fishing rod holders...
thingiverse
Greetings, This is a simple fishing rod rack I made to get my rods out of the way. It is 8" in length. It took roughly 3 hours to print one holder with the Ender-3 printer at 120ms speed. Note: During installation, leave enough space on both ends so...
thingiverse
You need one base where the rod bases sit and one clip. I have a large and small version of each. The large version has a depth of 64-70mm. Print this for med-heavy rods. The small version has a depth of about 40mm so the rods hold tighter to...
thingiverse
Fishing pole rack. Designed the large hooks to pinch most fishing pole handles so they are more secure. I use 3 different brands of rods and all of them fit great in the handle hooks. There are 2 parts in this print. One alternates: handle,...
thingiverse
You need one base where the rod bases sit and one clip. I have a large and small version of each. The STL files with large in the title were the original design and work great. If you have larger tackle, you may want to use the large. They have a...
thingiverse
This thing is a pair of mounts for holding fishing rods. You can store four rods in alternating directions. They work well mounted on the sides of a boat. Mounting holes are included for #8 screws. Print 4 of the curved flex fingers, 4 of the...
thingiverse
This rod mount is designed around my Shimano Zellous Rods. The hooks measure 18mm towards the butt and 10 mm towards the middle of the rod. ...this is designed to use drywall screws and ankers that are 4 to 5 mm in diameter and a countersunk head.I will...
thingiverse
Display your rods while also protecting them by storing them above your head! ... The model was designed to have a LxWxH of 5.25in(133.35mm) x 2.93in(74.422mm) x 0.50in(12.7mm)
thingiverse
I based the design off of thing 1753721 by jcox10 -- [2 piece fishing rod holder clips](https://www.thingiverse.com/thing:1753721). That design was only for a specific rod though. I made a model in openSCAD that can be customized for any rod. You...
thingiverse
This is a super low profile and easy to print rod rack optimized for Light To Medium-Heavy action Spinning and Casting rods. This Fantastic set can be printed in Just over an hour and has been continuously holding my two bait-casters for over 4...
prusaprinters
The rod can be held using bungee straps - ideal for beach fishing or short trips - and can also be attached using a zip-tie for longer trips or more security.Best printed out of PETG as this will withstand the sun's rays better (at least in...
prusaprinters
The open part of the rack features tabs at either end for hooking a bungee cord to retain the rods. I've included screw holes with passthrough holes for a screwdriver. </p><p>Each part is broken into 2 bodies to fit on an average print plate. I...
thingiverse
The STL file includes 2 mirrored parts which together make one rod-holder capable of storing 4 fishing rods. This model is 270mm wide and will not fit on smaller beds. The three horizontal holes are for mounting. The 2 vertical holes are for...
thingiverse
I wanted a rack to transport some flyrods around town so that I don't have to break them down when going from one fishing spot to another. I've seen a couple of products out there on the market but this seemed like a good DIY situation. Probably...
thingiverse
The fishing rod clips are the perfect solution for carrying and storing your fishing rods. ...The easy to use clips attach rod halves together.
thingiverse
Simple clips to hold the pieces of a 2 piece fishing rod together for transport or storage. Sized specifically for a UglyStik GX2, but would probably fit other rods. Checkout https://www.thingiverse.com/thing:2959608 by benjamenjohnson for a clip...
thingiverse
This design looked perfect for our fishing rods but my printer isn't big enough to print the whole thing. So I made two smaller versions that fit my printer. I didn't scale it down, just cut out the middle to make it fit my printer. You gotta...
thingiverse
This is a fishing rod rack that I mounted on the ceiling of my garage to organize my fishing rods. It holds up to four rods and can also be mounted on the wall horizontally. Hope someone else can get some use out of these. I have a 300mmx300mm print...
thingiverse
My print bed was not larger enough on my Anet A8 and I only have two fishing rods! Great concept by Auxon, I just needed something smaller. ... Thank you Auxon!
thingiverse
I made a circle form for the upper part, it doest hurt the rod anymore.
thingiverse
Customized version of https://www.thingiverse.com/thing:2959608 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2959608