five dollar filament 3d models
191894 3d models found related to five dollar filament.
thingiverse
......Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=45101 Instructions Using the following options: spool_width = 40 spool_walls_diameter = 150 spool_walls_width = 3 filament_diameter = 2 unit = 1 spool_hole_diameter = 40
thingiverse
This stabilizes the 200 gram spools used with ProtoParadigm's $5 Filament. It's not necessary but helps the spools stay in position. The part was designed for a Wanhao i3 reel holder but would work on any that could accept a 34mm ID reel. ...Print...
youmagine
This spool is sized for Protoparadigm's convenient $5 filament sample packs. It uses plastic-friendly threads + a locking detent to disassemble and reassemble simply & reliably. ...The spool ID is 50mm, and an adapter is included to go down to 25mm. The...
thingiverse
This spool is designed to securely hold spools of $5 Filament from ProtoParadigm. The halves screw together. This was inspired by another design I saw, but wanted some changes, so I designed this from the ground up to use less plastic, have space...
thingiverse
Spool Holder for ProtoParadigm's five dollar filament Stabilizes the spool while printing. The hubs on both flanges thread together and clamp the center hub of ProtoParadigm's filament bobbin to hold it securely while printing. ...38mm ID x 120mm OD...
thingiverse
Quarter turn Spool Holder for ProtoParadigm's five dollar filament UPDATE I just added a new version of the male flange called "undersized". Some people have no issues but some say the detents are too tight. The undersized flange detents are...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=127588 Instructions Using the following options: REVERSE_BOTTOM = Five dollars BOTTOM_TEXT = Unlimited TOP_TEXT = Three Suns TEXT_HEIGHT = 5.0 THICKNESS = 3.2 SPACING = 0.8 REVERSE_TOP = Store...
thingiverse
... for the simplest spool holder. ...It holds the 5 dollar filament spools straight and keeps them from flinging themselves everywhere. I use this along with bolting down the spool holder to the table with a flap of cardboard. ...Works great for me!
thingiverse
I really like 5 Dollar Filaments from http://www.protoparadigm.com/5DollarFilament/, especially for project that I do not need a large amount of a special color. Just do not like the flimsy spools they come on. Design this replacement that can be...
thingiverse
This handy little tool lets you cut bottles of various sizes and requires **less than $5** in hardware. I wanted to be able to cut wine bottles into glasses but didn't want to pay the $15-$35 that most cutters cost. So, I picked up some screws...
myminifactory
An adapter for $5 filament spools. The spools used by ProtoParadigm are creative but they will jam easy on a spool holder. This adapter can be a little tight to fit into the spool but thats intentional because if the spool comes loose your print will...
thingiverse
This is a small spool support that I made to hold the little spools of filament sold by protoparadigm under the FDF ($5 filament) brand. I found that putting the spools without support on a rod like I use on the Wilson II design (Ø 8mm to 10mm)...
thingiverse
This spool works with the Mp Select mini spool holder, it snaps in place on the 5dollar filament spool to provide stability.
thingiverse
This "tray" contains a swiveling pass-through filament guide and reinforcing rings for wiring/vent holes. All these parts are designed for a 1 inch hole. I had very good results with a new 1" hole saw at slow speed. An annoying property of...
thingiverse
I remixed this filament holder to have a 29mm hole so it fits on my homemade PVC-based spool holder.
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
cults3d
Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259
thingiverse
Customized version of http://www.thingiverse.com/thing:193941 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193941 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:58259 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options: word = $$
3docean
Originally created with 3ds Max 2016 and rendered with VRay 3.06.03 This model is suitable for use in broadcast, high-res film close-up, advertising, design visualization, etc Modeled for subdivision – only quads and tris polygons. ...This model...