flashforge adventurer 3 filament 3d models

This arm will work with pre-existing nut for ender 3 pro filament spool holder

Ender 3 pro / V2 filament spool holder with bearings and threaded clamp.

Ender 3 pro / V2 filament spool holder with bearings and threaded clamp.

these are 2 versions of improved optimized filament guides for the ender 3 v2. ...

Halter und Führung für eine zweite Rolle Filament am Ender 3

these are 2 versions of improved optimized filament guides for the ender 3 v2.

Creality (Ender 3) Filament holder 80mm spools that dose not brake when you print it. ...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. ...This is a filament guide to help the filament enter the extruder at a better angle without...

I rotated the filament guide out 90 degrees to take the strain off the guide as I am also using the Filament Roller Guide for the Ender 3

Snap on a stylish filament guide accessory featuring a convenient filament rest wheel directly into the original extruder component of the Ender 3 printer model.

Ender-3 Pro Filament Sensor Mount Remixed from filament guide: https://www.thingiverse.com/thing:3052488 The filament I bought from Amazon (2 pack) $11 https://www.amazon.com/dp/B07N2GQHQT

Filament guide for the Ender 3 V3 SE printer.This part realocates the filament sideways, so you can remove the filament spool from the top of your printer.Printable without suports with a clean look.

Filament guide for the Ender 3 V3 SE printer.This part realocates the filament sideways, so you can remove the filament spool from the top of your printer.Printable without suports with a clean look.

made for use with bearing ZNL 1000806 2RS 61806 6806 and ESUN filament coil fix some problems with filament stuck replace default filament holder from ender 3 v2 neo, use default nut

This is an updated version of "Ender 3 Pro Filament guide" Improvements: 1) Simpler design and shorter print time 2) Eliminated screw, nut and t-nut 3) The PTF tube makes the filament flow smoother

This adapter allows a 1 KG roll to fit the default Ender 3 Pro filament roll holder. ... Works best if use in combination with the Creality Ender 3/5/CR10 Filament Spool Retention Clip by sapphitron. ...

This is an updated version of "Ender 3 Pro Filament guide" Improvements: 1) Simpler design and shorter print time 2) Eliminated screw, nut and t-nut 3) The PTF tube makes the filament flow smoother

Simple Upgrade Guide for Fluxion's Tevo Tornado Roller Bearing Filament Guide on Ender 3. ... Since I upgraded my Ender 3 to a dual gear extruder with two filament guides, the original guide became too lengthy and cumbersome to navigate.

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot

these are 2 versions of improved optimized filament guides for the ender 3 v2. Category: 3D Printer Accessories

This is used to mount the Ender-3 S1 filament sensor on the extruder. ... Use M3x8 screws or longer.

Sleek filament feeder optimizes printing performance. Securely attach it to prevent unwanted tension. ...Designed specifically for Ender 3 users.

I crafted a straightforward cover for the filament coil atop my Ender 3 to thwart dust accumulation entirely.

Elegoo Nepture 3 Pro Bracket to move the filament holder to the front and down to fit on a shelf.

Filament guide for Ender 3 v3 SE.I'm reusing bearings from a spool stand that I don't use.

this is a optimized filament guide for the ender 3 v2. ... print on side, pully side down.

This is a filament guide for the Creality Ender 3 PRO for use with 1/8" bowden fitting. Only tested on Ender 3 PRO, do not know if it will fit original Ender 3 or V2. ... Designed to work with [my filament guide/cleaner...

Works with the stock Ender 3 / Ender 3 Pro spool holder retention nut Intended to be used with filament spools with smaller openings than the standard 1kg spools

This's the ender3 s1 pro filament guide that works with rice bucket(Moisture-proof box). ... 3mm & 3.5mm bushings chose by yourself,3.5mm is recommended.

Ender-3 Pro Filament Sensor Mount Remixed from filament guide: https://www.thingiverse.com/thing:3052488 The filament I bought from Amazon (2 pack) $11 https://www.amazon.com/dp/B07N2GQHQT Print Settings Rafts: No Supports: No Resolution: 200 Infill:...