flashforge adventurer 3 filament 3d models

This high-detailed model was part of our May 2021 release on Patreon. If you are interested in seeing the full set, please visit our store. You can aslo support us on Patreon to get the models much earlier. https://www.patreon.com/epic_miniatures ...

I found that my original version tended to rock itself loose when the tubes pulled against it. ...This may be only my printer, but I found that by extending it like this and using all of the mounting clips the problem was resolved.

Having tackled some problems with the initial model, primarily the collapse of one of its arms, I decided to create a revised version two. To prevent similar failures in the future, I strengthened the arm and replaced the original glue-in stud with a...

I was particularly impressed by this design on Thingiverse: 735350, but my fittings required 1/8" NPT threading so I adapted it slightly to accommodate the smaller hole size. To fit my specific needs, I drilled out and threaded the hole to accept...

To enhance my Creator, I added a Dust Filter mounting option on it. The Bevel modification was done for increased strength and fewer breakage points. For simpler installation, the piece was divided into two parts. ...However, I think there's room for...

The original side loader arm worked great until the stress on the corner of the hook caused it to break. I modified the original loader arm file using 3D Builder to make it thicker so it (hopefully) won't break again. Only the part near the...

The ultimate upgrade is here, with a revolutionary drop-in replacement for those flimsy snap tube holders that needlessly require a zip tie. Simply install it with the factory-provided screw, effortlessly securing your print job. To make the most of...

<p>you will need plenty of supports. ...I used PLA with 25% infill.</p> Category: 3D Printing

This model was created using Tinkercad's robust design tools. ...You can make changes to it directly online at Tinkercad's official website, which is located at https://www.tinkercad.com/designs/1rHgQ7kAAVG.

Modified reel designed for high-performance use, featuring a robust 20mm hole for secure installation and a substantial 48mm width for enhanced stability.

I discovered that my initial design had a tendency to wobble excessively whenever the tubes strained against it. ...This might be an issue exclusive to my specific model, but I managed to rectify the problem by lengthening the structure and utilizing...

Here's a quick fix to shrink the hole down to perfectly accommodate a 4mm tube. Just remember, you'll still need 3mm wide zip ties if you decide to use them. ... edit: I made a mistake earlier and referred to 3mm as a tiny detail.

This is a remix of the original https://www.thingiverse.com/thing:1396391 Really liked the idea of the rear fan with my flexion kit so I edited the original to fit! Still supports the original screws and fan mods! ...Added large holes at the top to...

I've been using the 2016 edition of my multi-width bracket, and it turns out that's actually designed for the 2015 model. ...Because of the open clips on the v.2016 Creator, this bracket may not grip as securely as the one made for the 2015 version...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

A Customized 75mm Wide Version of a Popular Thingiverse Model, minus the MakerSome Logo.

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

This is a remix of https://www.thingiverse.com/thing:805717 I made some adjustments to fit the latest Creator Pro (2016+)

you will need plenty of supports. ... I used PLA with 25% infill.

This filament guide was designed to help smoothen the flow of filament from the spool to the extruder of the Ender 3 V2 printer. The filament guide comprises of four parts. After printing the parts, they can be easily assembled by press-fitting...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

This is a remix from: BTT Smart Filament Sensor Mount - Ender 3 https://www.thingiverse.com/thing:4611661 Ender-3 / CR10 / CR20/Tevo Tornado filament roller guide https://www.thingiverse.com/thing:3184816 I wanted simple mount for BTT sensor filament...

This is a simple mount for a filament runout sensor that fits the Ender 3 / Ender 3 Pro printers. See the image to determine whether it will fit the specific sensor design you have. The filament intake tube was designed so that it can accommodate a...

This is a remix from: BTT Smart Filament Sensor Mount - Ender 3 https://www.thingiverse.com/thing:4611661 Ender-3 / CR10 / CR20/Tevo Tornado filament roller guide https://www.thingiverse.com/thing:3184816 I wanted simple mount for BTT sensor filament...

This filament guide was designed to help smoothen the flow of filament from the spool to the extruder of the Ender 3 V2 printer. The filament guide comprises of four parts. After printing the parts, they can be easily assembled by press-fitting...

SUPPORT GUIDE FILAMENT ( LOW FRICTION) ENDER 3 / ENDER 3 PRO

SUPPORT GUIDE FILAMENT ( LOW FRICTION) ENDER 3 / ENDER 3 PRO

... the stability. There are three versions of the filament guide: one with a square pin of 6.4 mm; one with a smaller pin of 4 mm; one without a pin. Print in 3 pieces: -filament guide (the version you prefer) -axis -roller Hope you enjoy it! ...

This prevent the filament to touch the greased rod and clean the filament at the same time. So you have two solutions in one! There are two parts, the body that is held by the rod screws, and the lid of the sponge container. It was designed for...