flashforge adventurer 3 spool 3d models

This adapter mounts to the original spool holder allowing you to use third party filament reels.

Improved weak design. ...Reinforced mount point. Allows for the mounting of a standard (less terrible) extruder onto an Adventurer 3 or Voxel 3D printer while retaining filament runout sensor support. ...Fixes extruder skipping steps.

Custom Air Duct Lever Optimized for Adventurer 3 Adjustable Air Duct Fans with Power Control by CipDV. ... This enhanced lever boasts superior strength and a sleeker design compared to its predecessor, while being significantly simpler to print.

This is a filament cover for using 1kg filament with Adventurer 3. Since 3D output cannot be done at once, I divided it into many parts and output it. ... Check my blog:(Japanese only) https://purunpurun.com/cover/

To see just how well this spool performs, check out our demonstration video: https://youtu.be/Yx6WwHR1QlI Here are the print settings we used: * Printer: Creator Pro * Rafts: Not necessary * Supports: Yes * Resolution: 200 microns * Infill: 30% *...

Designed as universal spool holder. Print both parts without support. ... 0.2mm-0.3mm layer height 20% infill

To accommodate a wider range of spool sizes, the cylindrical cylinder where spools rest has been scaled down. ...Pins and holes for the pin are integrated to keep spools securely on the holder.\r\n\r\nNote: The Plate object is the cylindrical holder,...

A few quick notes:The sleeve is optional (recommended for cardboard spools)The tall handle is to help align the arm with the holster, NOT to support the weight of the spool by itself (ie. ...spool changes are a two-hand operation)

... for Filament Mate dryer box. ...Makes Spool spin much more freely. Has provision of the original Hygrometer. Can be printed support free. On purpose designed a little "too long" - when lid is mounted it will hold spool holder under pre-tension. ...

Taulman Bridge Filament takes a slightly different form, boasting dimensions of 3/4 inch (19mm) by 70mm long. A reliable connection is secured with an M6 screw and washer. I've included the 123Design files for your convenience, allowing you to...

I ordered another one, but found that the inside of the spool was not the same as the default that came with the printer, it was a bit wider, so it would fall off the holder. ...This is meant to be a clip so that you can put the spool on, and then the...

The device known as a spoolholder is specifically designed to accommodate spools that are exactly Ø38 x 91-92 mm in size.

I was struggling to figure out a way to attach my Pi to the FlashForge Creator Pro without compromising its casing with unsightly holes. Since I needed to add filament support anyway, I cleverly integrated both issues into one seamless solution.

Here is the rewritten text in American English: "I created this design for my FlashForge Dreamer so I can attach one to each side of my printing cart. After searching on here, I found some designs that were too large to fit on the Dreamer bed, so I...

I appreciated the straightforward spool holder design found here: http://www.thingiverse.com/thing:805617. However, I required a slightly longer version to accommodate my wider spools, similar to the Gizmo Dorks rolls. ...To achieve a more secure fit, I...

Spool adapters that shift the offset provide a tighter fit of the lager spools. ...Its a 50mm outer bore so it accepts Matterhackers filament which is slightly smaller than the others I've used such as GizmoDorks, IC3D, Inland, ColorFabb, 3D-Fuel,...

I couldn't get the top of the side part printed properly for some reason; it printed so brittle it snapped every time, so I designed this; it's smaller, quicker to print, and uses the stock horizontal spool holder. For the spools I use, the center...

... of rolls of 3D Solutech filament just taking up space, but they won't fit in my Creator's stock filament holders. ... These hub adapters should work with any spool hubs that are at least 57mm wide. ...As long as the spool itself is less than 60mm wide.

These holders fit most filament types, particularly the Hatchbox ones, which is a major upgrade from the large Flash Forge creator pro spool holders originally supplied. Right and left side separation keeps spools at safe distances from the take-up...

You'll adore this setup if you're always swapping out filaments. Version 2 This revised version accommodates up to five spools of filament with improved support. Typically, I keep three spools on it and slide the one in use to the center of the...

However, its internal spool holders fail to cooperate effectively with non-standard FF spools. These spools swap the side "windows" for new 3D-printed holders. I have successfully installed these on two separate machines, but they presented distinct...

My local supplier for filament uses a spool with a smaller core size of 30mm, which contrasts sharply with the larger size that my CTC printer's original spool holder can accommodate, approximately 38mm or more. I couldn't locate an alternative...

This new setup makes it 100% easier to swap out spools, thanks to rowokii's universal spool holders and fast-fit clip. I used 15mm aluminum tube from In-Excess for this project. However, you can use whatever materials you have lying around in your...

A Versatile Spool Holder for Easy Printing Access Edit 2: The Enhanced Model Accommodates Larger Rolls, Ideal for the Most Demanding Print Jobs, Particularly Suitable for Those Using High-Demand Materials Such as Hatchbox Filament

I was eager to create a spool holder that would keep the actual spool snugly close to the printer and maintain an efficient filament guide. Moreover, I thought it would be a great idea to incorporate a cap to prevent the spool from toppling over, a...

To accommodate my spool holder's restrictive holes, I opted to create a custom spool for my 618 nylon spools that utilize the same size of filament, 1.75 mm. A central hole of 32 mm will adequately serve most printers in this setup. **Assembly...

... thought that it might be useful. ...I have a Qidi Tech 1 and X-Pro, I just tested it on the Tech 1. It fits a 1kg printer spool perfectly, with some slack, so should work with other 1kg Spools. ...You will just need an M10 x 50 bolt, nice and simple.

This adapter is meant for BaronWilliams's Large Spool Holder, available here:http://www.thingiverse.com/thing:415744 A straightforward spool rod cover was designed to be oversized with a lip on one side. This allows ProtoParadigm filament use inside...

These hub adapters should work with any 57mm or wider spool hubs. So long as the spool is less than 60mm wide. You shouldn't need supports, print with the wide side of the adapter oriented to the build plate. ...Infill is up to you, I did 15% ...

Updates: Current version (0.01) tested successfully with 50% of my spools, but the arm is too thick for some smaller spools. Resized version for smaller spool axles en route soon. 0.01 - Upgraded to enhance the arm and make it larger (if you have the...