flashforge adventurer 3 spool 3d models

Two adaptors are included, one for original spools and one for Kaiserlich24 spools. To print the spoolholder, a minimum of 50% infill is recommended for larger spools. Printing with 80% infill will produce an even better result. If you need more...

http://www.thingiverse.com/apps/customizer/run?thing_id=1733767 Print Settings: Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 0.25 Infill: 10% Instructions: Using the following options: spool_hole_diameter = 30 spool_width = 80...

... Spool This Suits: Hole diameter is 55mm. Depth is 90mm. See picture 5. Print Settings: Printer: FlashForge Creator Pro with Dual Flexion extruder fitted Raft settings: None Support settings: Yes Resolution setting: 0.2mm Infill percentage: 20%

I'm glad to offer a remixed version of the External Spool holder for the FlashForge Finder 3D Printer by CreativeTools. This revised version lets you securely attach the spool holder directly to the side of your machine. It's designed to print in...

This is a very straightforward spool holder for FFCP.\nIt demands that you attach a piece of PVC pipe and an M10 bolt\nto see: http://www.instructables.com/id/Spool-Holder-for-Flashforge-Creator-Pro-FFCP/\nPrint Settings\nPrinter: \n Flashforge...

The spools of filament I purchased refused to seat properly on the standard spool holder supplied with my FlashForge printer, which boasts a 66mm x15mm spacer at its base. In stark contrast to the spools that came bundled with the FlashForge, the new...

I spotted studiohals' spool holder for the FlashForge Dreamer and it didn't quite fit for my FlashForge Creator Pro / PowerSpec 3D Pro, so I made some adjustments. This design uses the spool holder that came with your printer to load filament. Simply...

---------------- [English] Adaptation of the mjoaris spool holder (initially for Ender 3) for installation on the Flashforge Creator Pro 2 (2020). The mjoaris's original project is at this address https://www.thingiverse.com/thing:3209211 If you...

To convert a large spool of filament for smaller spools used with Flashforge Finder printers, follow these steps: First, you'll need an M10 x 65mm coach bolt and nut to connect a power drill with speed control as an axle. I secured the screw in...

A filament holder designed specifically for CR-10 users who also use FlashForge Finder spools. ...This holder fits seamlessly with the original nut that comes standard with your CR-10 printer and only requires one screw for installation, as the other...

The wall holder is specifically tailored to support the original spool holder of the Flashforge Creator Pro 3D printer. It also accommodates alternative holders designed for this model, providing flexibility in setup options. Initially, I had mounted...

I had made a couple of the http://www.thingiverse.com/thing:12470532015 Flashforge Creator Pro Universal Spool Holder Print Friendly things, but in using them I wanted to keep full depth spools and half size spools held firmly to the machine face. A...

We needed a setup where filaments spools could effortlessly slide onto any spot on our 3D printer, with easy access and seamless integration into the extruders. This is the first installment of custom parts designed specifically for the FlashForge...

Due to the limitation of the spool dimension on the Flashforge Finder, I have decided to design an external spool holder. Every 1kg of filament could fit with this design.Every part on this design can be print with the Flashforge Finder.No glue...

This external spool holder is designed specifically to work with Flashforge Inventor 3D printers, although it may also function properly with Flashforge Dreamer and Dremel Idea Builder models. To complete this project, you will need a 5/8 inch round...

Ich konnte für meinen neuen Flashforge finder 3 keine Werkzeugbox finden, die ich oben an den Drucker klemmen kann...

This accessory lets you attach a 30mm-hole spool to a CTC or Flashforge 3D printer. It's my first SketchUp drawing attempt, with more photos coming soon. Check out this video: http://youtu.be/B6HgoJb__j8 For assembly, print the NUT thrice - once for...

Had some old Flashforge filament spools laying around, however the spoolholder to my creality CR-10 is too wide to accept them. So I made a new spool holder using TinkerCAD that fits the nut from creality. There are other designs for this purpose,...

Clip-on, rear-mount, dual spool holder for the Flashforge Finder. ...For assembly instructions, see: [Google...

Flashforge Dreamer Left and Right Wall Mount Spool Holders These mount to a wall or cart (in my case) I was able to find some on here but they were to large to fit the dreamer bed, so I came up with these to take care of that. ... no supports, raft,...

This is an external spool holder for the flashforge finder with a working end-of-filament sensor. To assemble, you need a soldering iron and some desoldering tools as well as a hot glue gun. You will also need a multimeter. ... You will also need a...

This is an external spool holder for the flashforge finder with a working end-of-filament sensor. To assemble, you need a soldering iron and some desoldering tools as well as a hot glue gun. You will also need a multimeter. ... You will also need a...

This filament spool holder is designed for Robo 3D Printer Filament used on the FlashForge Creator Pro. Although the entire design was thoroughly re-created, its foundation remains rooted in http://www.thingiverse.com/thing:930910. We're including...

This is my latest creation: a 608 Bering Spool Mount Replacement designed for the FFCP/PS3DP Printers with 30mm Tube Mounts for Filament Spools. This innovative design is perfect for spools with a 52mm Inner Diameter and a Width of 62-70mm, making...

I saw studiohals' spool holder for the FlashForge Dreamer. It didn't quite work for the FlashForge Creator Pro / PowerSpec 3D Pro, so I remixed it. This is made to use the spool holder that came with your printer already. To load filament, just put...

I switched some time ago away from the spool holders at the back of the printer, because they are high friction compared to having a spool holder that runs on skateboard bearings. That leaves these old spool holders hanging off the back of the...

... the original design. Please feel free to fine-tune this spool holder using the Customizer to ensure it fits your specific spool perfectly - for instance, I believe it would be suitable for Hatchbox, but you should verify this information yourself!

This FlashForge spool holder design was inspired by two existing creations: Thing 714533 and Thing 508896. I aimed to differentiate myself from other designs by avoiding metal screws and instead creating a holder with slots featuring a larger cone...

I was going to create a spool holder hole plug for the 2016 Flashforge Creator Pro, but then I stumbled upon tim-sweden's design. It was a great design, but it was clearly made for flexible filament, which I didn't have on hand. So, I imported it...

I'd like to share a quick and easy design for a spool holder specifically designed for the Flashforge Creator Pro 2016, which everyone knows has different mounting hole sizes. I created one for 38mm diameter filament. The design features two simple...