flashforge adventurer 3 upgrades 3d models

You get an Investigator Pilot Lady from our Mega Investigators Kickstarter. ... Scale: 32 mm Heroic Includes a presupported version

Miniature I've made for my Patreon's 2020 November release. All files on my Patreon releases come pre-supported for resin printers. Designed for tabletop gaming and dioramas. If by the time you are getting this miniature still November I recomend...

Yeah, very over-engineered, but I wanted it not to move and strong. Looks like it will hold way more than 1kg, haha. Printed the shaft so far, which is a very snug fit, and fits perfectly. Works amazingly well due to the center of rolls being...

I haven't had a chance to test it yet, so I'll wait until I need to replace the cable before giving it a try.

2 Sets of Clamps to tighten your glass plate to the bed and do some fine-tuning on the leveling.

Recently I connected my printer to our WIFI network so I could upload code without the USB port and check the print's status using the built in camera when I'm somewhere else. Unfortunately the camera points directly at my desk. ...Obviously I don't...

Remixed external bowden tube connector. I recommend Capricorn Tubing, but whatever you have is probably fine. Source Models: https://www.thingiverse.com/thing:3626515 https://www.thingiverse.com/thing:3775453 The BowdenBracket and...

This is a basic, very sturdy filament spool holder. It holds normal 1kg spools. Print this upright with supports. I printed this with 50% infill but you could probably decrease this without any issues. This holder fits around the original spool...

A slightly modified an duct for Flash Forge Creator 3 pro.

The Ender 3 X-cover Blink Camera Mount found here: https://www.thingiverse.com/thing:4674208 & the Flashforge Adventurer 3 Bed Levelling Holder found here: https://www.thingiverse.com/thing:3143221 I loved the idea of having my Blink Mini follow the...

A custom rig to stabilize a Nokia 3 phone with Gel Case for capturing smooth timelapses. ...I utilized a sturdy M6 bolt and reliable wingnut to firmly attach both the mount and the case to the printer.

Designed to fit Creator 3 v2, I printed this in Iron Grey ASA-X to match the colour of the printer and ensure that it did not get affected by the heat of the printer and direct sunlight. ... Prints without supports

A ~10mm spacer that I made to raise a slightly oversized spool that was rubbing on the lower surface of the Creator 3's stock side spool holder compartment. Can be scaled in the vertical axes in FlashPrint to make the spool sit higher or lower if...

The original spool holders of the Creator 3 won't hold those spools very well, they kept on leaning down with the risk of falling. Plus I couldn't close the side door without the spool being jammed. Solution: a 50mm OD and 70mm deep spool holder...

Ich konnte für meinen neuen Flashforge finder 3 keine Werkzeugbox finden, die ich oben an den Drucker klemmen kann...

It contains: 1) upgraded version of "mirrored" fan duct for opportunity to install the BL Touch sensor mount on Ender-3 carriage. 2) BL Touch sensor mount It was designed for Ender 3 and wasn't tested on other compatible printers. BL Touch sensor...

This is organizer will hold 3 hot ends for the Flash Forge Adventurer 3 and 4 series 3d printers.Use some double stick tape to install it inside the printer someplace.

Dieser Werkzeughalter arbeitet mit dem Flashforge Finder 3 zusammen, um Werkzeuge wie Seitenschneider, Schraubenschraubenzieher, Inbusschlüssel usw. an einem leicht zugänglichen Ort aufzubewahren. Der Halter erleichtert auch den Wechsel zwischen...

I've been asked on a few occasions to share files and references to the ongoing upgrades I'm doing on my Kossel Linear Plus, so I figured the easiest way to let people follow my progress is to create an ongoing blog. Here's the first installment of...

These are Adventurer 3 Filament Spool Box v2 Update Parts for v1. If you use this You have to cut 5mm off center pole parts because filament spool hit to this door parts. ...Or please print new one.

I wasn't able to find a spool holder for my Monoprice Voxel, so I made one myself. I've already used about five or six 1kg filament spools with this holder and it's worked flawlessly every time. ...Now I can print any size spool of filament that I want,...

Created parts to avoid having wires hanging all over the place in my Ender 3 S1 Pro after installing the Sonic Pad and Nebula Camera. I've installed the wiring ducts on the back of the machine and a little bridge on top to have all wires routed...

Ich war auf der Suche nach einem Multi Spulen Halter für meinen neuen Flashforge finder 3 und konnte keinen finden. Ich habe den Filament-Halter von cysayles https://www.thingiverse.com/thing:2796365 für den neuen Finder angepasst und noch zwei...

This is an attachment for Mathicj's excellent spool holder extension for the Adventurer 3. I printed the arm at 25% infill for a little extra strength while retaining flexibility, no raft or brim. I printed the cap at 100% infill, otherwise...

Easier Heizbett setup with 3 point adjustment Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 100% Notes: 2 Shells Print in ABS. Instructions 3.5mm hole front center between remaining holes...

I needed to save space and access the filament easily. I created this :-)(easy to print NO raft or support needed) 15% infill should be enough.It mounts on the right side top! Works for both - small and normal 1kg. ...filament rolls.𝔗𝔴𝔬...

I needed to save space and access the filament easily. I created this :-)(easy to print NO raft or support needed) 15% infill should be enough.It mounts on the right side top! Works for both - small and normal 1kg. ...filament rolls.𝔗𝔴𝔬...

First mount the base on the printer, after that you can slide the holder to the base. WORK IN PROGRESS, still need to make the testprint but should fit according to the drawings.