flashforge adventurer 3 3d models

This is a tool holder that I designed to hold all my tools I use. It holds: 2" putty knife/scraper Glue Stick USB Stick Stylus Nozzle Cleaner Small Screwdriver Small hex key I affix it with double sided gorilla tape and mount on the back...

This is remix.YouTube video:https://www.youtube.com/watch?v=mTTpbSJEPMAVisit site:https://printyourfix.com/

Adapter to take the tube out of the printer. Drill a.375" or 9mm hole in the center of the original door and cut the inside so that the tube is not restricted. ... For best results, make the M5x0.8 thread after printing Use a Push-to-Connect Tube...

Call this an extreme make of the original thing. Full Size make of the door, and full size make of the base. A dissection of the base was to minimize the printing issues. The base still needs to be glued on the long axis(these two *.stl files). ...The...

Tight-fitting spool holder. ...Print at location indicated by image, with no need for additional support structures.\r\nOnly a few minutes of sanding will be necessary to achieve a smooth finish.\r\nAs an alternative, I've included the split version as...

in the process of getting a more airtight enclosure of the printer (and getting higher inner temps) i have created this cover to closes the opening visible over the filament roll location. ... to ease the installation it is best to lower the print head...

I had a problem with layer shifts due to the nozzle bumping into object and shifting whole table slightly. This is a solution. You just put it like in the picture and forget about it. ...Does not interfere when sliding the top plate.

Remove the tube from the printer immediately. Drill a hole of 9mm or 0.375" in the center of the original door and modify it so that the tube has an unobstructed path. To achieve optimal results, create the M5x0.8 thread after printing is...

... a New Internal Spool Wheel Design for the Printer. Additionally, an Adapter Was Added for the New Hose Wheel. Original File Link: Https://Www.creativetools.se/Misc/Doc/Flashforge/Adventurer-3/Extended-Spool-Holder-for-Adventurer3-Stl.Stl

I crafted an adapter specifically designed to fit snugly inside the FlashForge Adventure 3, accommodating their unique size filament spool which is smaller than a standard 2.2 Lb. spool. ...This thoughtful design prevents any wear on the machine's...

### I have remixed the 9 point calibration test by Jakoboster so the squares are .3 mm high and centered better. .3 mm and 103 extrusion rate are the recommended first layer height for the Fula-Flex 2.0 PEI plate I changed to. ...

This is a spool holder adapter for the adventurer 3 (old model). ... It works with the door closed.

I use 0.3mm first layer for my Adventurer 3 for better first layer bed adhesion, heres a test file for it anyway

After recommending the adventurer 3 to a couple friends this past Christmas I realized that the spool holder by gozengamine doesn't work with the newer adventurer 3s. ...I meshed some other model with the one he made and I THINK it will work but I...

Slicer: Simplify3D Nozzle Diameter: 0.4 mm EM: 0.9 mm EW: 0.4 mm Retraction: 3.50 mm Retraction Speed: 30.0 mm/s LH: 0.2 mm First LH: 0.2 mm Top Solid: 3 Bottom Solid: 3 Perimeter Shell: 2 Infill Pattern: Rectliniear Infill Percentage: 15% Print...

Because the bed of the Adventurer 3 is only 150mm x 150mm, I've reorganized the 5-part storage cube into a 2-part and a 3-part design. I then removed the standalone 1-part cube above and created a separate larger cube attached to the 3-part cube to...

The g-code files in gaaZolee's post did not seem to work properly in my Adventurer 3. So I tried using Cura with config files for the printer posted on GitHub to convert the STL. Cura has some handy g-code editing scripts to speed things up. So,...

Hi guys - just discovered that another version of the FF Adventurer 3 appears, called BRESSER 3D printer. This one comes equipped with a HEPA filter for printing - So I just tried to design something similar to reduce the smell while ABS printing. I...

This is a custom designed dust cover for the Y Axis rail of the Flash Forge Adventurer 3 printer. The printer's design prioritizes ease of use over frequent servicing, with all rods and rails easily accessible - except for the Y axis rod, which lies...

SmartTemperatureTower_PLA_180-225: https://www.thingiverse.com/thing:2729076/files Slicer: Flashprint 4.3.0 First layer thickness: 0.20 Layer height: 0.18 Fill density: 15% Fill pattern: hexagonal Base print speed: 60 mm/s Travel speed: 80 mm/s...

I've seen some clips for the adv 3 and a glass bed, and it dont work for me. So i designed some edge clips by myself as my very first project on FreeCAD. The glass bed is a 165x165mm plate from ebay seller: https://www.ebay.de/itm/303171068149 ...

This hooks onto the back of the printer, slotting in-between the grills at the back of the printer. I use large filament spools and need to remove the cover most of the time. When the cover is not attached to the printer, it can be safely stored at...

The Y-axis of the A3 features an 8mm rod with a sturdy carriage gliding on it using brass bushings. The carriage's considerable length makes it unlikely to be the source of the rattling sound. Although the Y-rod itself is not properly secured, it...

Print at 100% infill with 4 walls, and no parts cooling the first three layers. ...

This holder spins effortlessly. ... You'll need: 1x M5 bolt, a minimum of 20mm long but ideally up to 30mm 2x 608 bearings Spool specifications include: Maximum diameter: 200mm Maximum width: 80mm (when using the longer bolt) Internal diameter:...

Add a lid to the open part of cover Please print the following cover first https://www.thingiverse.com/thing:3184595 The lid is divided into an top side and a bottom side, and the two are connected for use. * Adv3cc_top.stl x 1 The top...

Was inspired by Moritzrath's 40mm fan mod. Used the original adaptor for a bit. Had issues after awhile with the fan coming loose and the very thin 30mm tube delaminating when made with ABS. Designed a more robust adaptor that is screwed to the...

The original fan blows on one side. Smooth surfaces are wavy, depending on the processing direction. I tried different models and couldn't find a suitable one. With this model it is possible to change the nozzle! The streamers are routed around the...