flashforge creator pro 2 upgrades 3d models

A smaller spool holder for the Creator Pro X is desperately needed due to the enormous size of the default ones, which completely obstruct custom filament from being used effectively. This innovative spool holder prints seamlessly without any rafts...

Love this SD card holder for the Rep 2, its perfect fit inside the hand-holds of my Flashforge Creator makes working easy. But what holds it back is not being long enough - this remix easily fixes that and now it can hold up to four SD cards in a...

A slightly modified an duct for Flash Forge Creator 3 pro.

The Creator Pro's standard accessory is a straightforward holder designed specifically to store Allen wrenches.

The default dimensions have a short SD slot that enables use with an SD socket featuring a 'push it to release' mechanism, such as the Flashforge Creator Pro. The model comes equipped with a built-in support wall, which facilitates easy printing...

Print Settings for this part are listed below: Printer model: FlashForge Creator Pro Yes, it does generate rafts during printing It doesn't have built-in support material. However, the option might not matter given that the infill density will reach...

The default dimensions boast a short SD slot that enables seamless use with an SD socket featuring a 'push to release' mechanism, like the one found in Flashforge Creator Pro. A built-in support wall is integrated into the model, allowing for...

Print settings are as follows: Printer: Flashforge Creator Pro 2016 Rafts: No Supports: Yes Resolution: 0.1 Infill: 30% Notes: ABS should be printed first, then acetone vapour the parts. The silicone will not stick to shiny surfaces. After printing,...

Printer Settings: Printer Model: FlashForge Creator Pro Supported by Printer: Yes Resolution Level: 0.3 Infill Rate: 40% Notes on Printing: To get these prints done, I set all three pieces to print in 0.3mm layers with a 40% infill ratio - except...

Flashforge Creator Pro). The model has a built in support wall that enables easy printing that gives cleaner results than using automatic support generated by slicers. The wall is one extrusion wide and can easily be removed with a X-acto knife. ...Once...

Do not use this model, use the original at http://www.thingiverse.com/thing:1132756 The reason for this remix is to provide a usable model with gcode that I produced from Slic3r for my FlashForge Creator Pro. The FFCP and Slic3r do not work well...

By default, the dimensions of this model incorporate a compact SD slot that facilitates seamless compatibility with SD sockets equipped with a 'push-to-release' mechanism, such as those found in Flashforge Creator Pro models. One notable advantage...

I created these custom glass clips for my FlashForge Creator Pro with a heated build plate and a 1/4" thick borosilicate glass sheet. I designed them to solve the problem of the glass plate being slightly smaller than the build plate. To get started,...

... time to time. ...It is difficult to get a wrench on the nuts to hold them when tightening. These key into the "V" and wont turn. There is also a spot for a 3mm lock nut to be pressed in. These also work on a Creator X with the Pro platform upgrade.

The shape is designed for the flavors of the FlashForge Creator Pro (2016 edition) that have the long-shaped feet, but they will fit any machine that has ‘feet’ shaped like a rounded rectangle of about 48×17mm, of at least 2 mm high. Of course you...

This is a top handle for the Improved Dome for Flashforge Creator Pro thing http://www.thingiverse.com/thing:1194887. It makes it easy to remove and place the dome using one hand.</p> <p>This thing was designed by customizing the parametric handle...

I love my Flashforge Creator Pro except for one ergonomic problem: when I stand next to it, I simply cannot see the display because it's too low and vertical. I need either to step back or bend down. Not anymore. This design provides a 45% slanted...

These holders fit most filament types, particularly the Hatchbox ones, which is a major upgrade from the large Flash Forge creator pro spool holders originally supplied. Right and left side separation keeps spools at safe distances from the take-up...

This holder was created for securing spray bottles and parts at the corners of a flashforge creator pro printer. As seen here, you can insert whatever fits inside it. Instructions A corner solution was sought out to hold multiple...

This is a custom handle for the Improved Dome that fits perfectly on the Flashforge Creator Pro. It makes it simple to detach and reattach the dome with just one hand. The design was created by modifying a parametric handle generator, allowing you...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Notes: Supports were only added to the drawer and infill was set to 100% for both the drawer and pegs. The drawer was printed horizontally. ...I...

This product specifically caters to the late 2014-2015 models of the Flashforge Creator Pro with slot spool holders. Best results are achieved when printing this model sideways, using supports at a 45-degree angle. This creation was influenced by...

Timelaps set up for Flashforge creator pro. ... To edit the gcode, use simplify3d > Scripts > Layer change script > add the text below: The basic code is: G90; Switch to Absolute Positioning G1 F9000 X-100 Y71; Move Quickly to New Location G1 F1000...

This is a simple side mounted PTFE tube holder for the Flashforge Creator Pro. The one that comes with the machine mounts to the back, and is best suited for mounting your spools to the back as well, but with a configuration like mine where you can't...

Inspired by this jig http://www.thingiverse.com/thing:810220, a user has devised a method to level a FlashForge 3D Creator Pro bed using a Harbor Freight digital indicator (SKU #93295).\n\nThe instructions for use are straightforward.\nBegin by...

------------------- I dislike the spool holder of the FlashForge Creator Pro 2016. Smooth rotation can be difficult depending on the filaments manufacturer. I have tested various systems and now use my own design. This system works with both big...

... 60mm in length and are spaced 81mm center to center. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20mm or less Infill: 15% - 100% Notes: The model was printed upside-down with adequate support throughout.

I couldn't find anything like this, but I needed a way to see what was actually coming out of the extruders on my Flashforge Creator Pro without using a flashlight. This is a simple piece, it clips onto the back of the dual extruder head and sits...

Print Settings: Printer: Flashforge Creator Pro Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Notes: Make sure to print in the orientation of the provided STL file for best strength and filament fibers orientation. The big oval bump requires...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Infill: 30% Notes: The filament tubes fit very snugly. To get one tube to go in, I had to remove a burr. If it's too snug for your tube, try rolling up some...