flashforge creator pro 2 upgrades 3d models

This filament tube holder is an add-on to the FlashForge Creator Pro (8cm tube spacing) to prevent the filament from getting tangled around the spool axis. This happens when the filament tube entry point is not aligned with the spool (as is the case...

In typical Chinese fashion, FlashForge Creator Pro 2016 models are often shipped with minor variations, such as some featuring small round feet instead of elongated feet like my model. User Shftatsix brought to my attention the update made to...

A premium tool caddy specifically designed for FlashForge Creator Pro models released after 2016 comes with a robust all-in-one molded side panel.\r\n\r\nMost tool caddies I've tried lack sufficient support, causing them to shift, flex, or break...

... Best regards, fdk Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 Infill: 20% Notes: This was printed with ABS Bed temp: 95 Extruder: 238 A bit of cleanup inside the magnet holes and it snaps together smoothly.

Print Settings Printer: FlashForge Creator Pro 2016 Rafts: No rafts are required for this design. Supports: Yes, supports are necessary to ensure a successful print. Resolution: A resolution of 0.2mm is recommended for optimal results. ... Notes Both...

I needed a more reliable solution for attaching back mounted spool holders on my Flashforge Creator Pro 2016. After conducting a thorough search, I couldn't find any suitable options that met my requirements. So, I decided to take matters into my...

These files are meant for the FlashForge Creator Pro, but will probably work for similar printers with a 230x155 mm build plate as well. If you have a QIDI Tech 1, you need custom files (https://www.thingiverse.com/thing:3032840) due to the...

... works well. Print Settings: Printer: FlashForge Creator Pro 2016 Rafts: No Supports: Yes Resolution: Creator Pro ABS standard Infill: 35% Notes: A support is only needed for the corner piece. ...I set my glass bed to 110c and used some hairspray.

This is a replica of the bracket that is part of recent editions of the FlashForge Creator Pro and similar printers with a dual MK10 nozzle carriage. It is mounted on the left side of the extruder carriage, and supports both the blower fan and the...

They also have cutouts for the print head to do its priming/wiping thing before it starts printing from the Creator Pro Cura profile I found and have been using. There are lips on the top edge of the brackets to fit glass plates that have had their...

This is a remix of https://www.thingiverse.com/thing:805717 I made some adjustments to fit the latest Creator Pro (2016+)

This is a universal FlashForge Creator Pro spool holder designed specifically for models that have a slot where the holder clamps securely. The design is adaptable to fit any spool size and diameter. The closing mechanism features a cone-based...

A week ago, I got my FlashForge Creator Pro 2016 and was blown away by its performance. However, some issues needed addressing. Firstly, it's really hard to fit filament spools from other brands in the included spool holders, but printing...

... Additionally, the box for the dial indicator can be modified to accommodate this design. Sincerely, fdk Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.20 Infill: 0.20 Notes: Printed on its side without support.

There are numerous spool holder designs available for the Flashforge Creator Pro, utilizing either a bolt or rod. I'm focusing on creating a new part that holds an 8mm bolt, specifically using a 120mm length bolt, as this is my preferred setup. ...

I purchased a FlashForge Creator Pro 2017 for my business and was frustrated by the difficult-to-reach rear spool holders that seemed cumbersome. Unable to find an acceptable alternative, I decided to design my own solution. These new spool holders...

Use this to test bed leveling of your Flashforge Creator Pro and verify flatness of the bed to detect bubbles after installing a PEI or BuildTak surface. Features: * Magnetic * Adjustable, easy to customize dimensions for precise printer tolerances....

A Reimagined Version of Chewbone's Flashforge Creator Pro Adjustable Glass Bed Bracket Enhancements to Corner Piece: The screw slot is now extended along the entire length of the corner, allowing for effortless removal and swapping of these...

I successfully printed this design on my FlashForge Creator Pro 2016 without issues. To help others print without supports, I've added images showing the support guides and cuts where the model's nerve is observed. This can be a useful reference...

... Z-homing at 50% speed (50mm/min) for accurate leveling. Moves rapidly to the front of the bed @ 9000mm/min! Fast blob (less than 1s!). Moves rapidly to start position @ 3000 mm/min. Go print faster! Print Settings: Printer: FlashForge Creator Pro

This is a remix of my FlashForge Creator Pro 2016 adjustable spool holder. This version has been modified to fit the older Creator and Creator Pro models (from 2015 and earlier) which use round holes for mounting the spool holders. This model also...

This is a remix of my [FlashForge Creator Pro 2016 adjustable spool holder](https://www.thingiverse.com/thing:1741096). This version has been modified to fit older Creator and Creator Pro models from 2015 and earlier, which use round holes for...

But in this case it is adapted for Flashrorge Creator Pro: 1. Depth made less at 5-6mm to fit back decorative wall; 2. Added a hole for fitting near the screw; 3. Made bottom thicker 0.75mm for resin printing. Printed on resin phrozen mega 8k as...

Taking apart the print head on a FlashForge Creator can be a real pain in the neck. Those spacers always seem to fall out and get lost, wasting your precious time and money. ...That's why I designed a printable replica of the original part - because...

These are the G-code snippets that belong with my PrusaSlicer (Slic3r) profiles for the FlashForge Creator Pro. Although I think the G-code is quite mature now, it's possible I will update it separately from the rest of the profile. Therefore, use...

This is an alternative version of the 50mm spool holder by RonPossible, for the recent revisions of the FlashForge Creator Pro. This is suitable for filament spools with a simple cylindrical hole of 50mm diameter and 60mm length. The differences...

These precision corner pieces are designed for seamless integration with the FlashForge Creator Pro when using a glass build plate from 3DUniverse (http://shop3duniverse.com/products/glass-build-plate). There are two distinct brackets to choose from,...

These are the G-code snippets that belong with my PrusaSlicer (Slic3r) profiles for the FlashForge Creator Pro. Although I think the G-code is quite mature now, it is possible I will update it separately from the rest of the profile. Therefore use...

This instruction comes directly from the FlashForge Creator Pro 2016 manual and represents a major limitation of this printer. However, after conducting extensive testing, I discovered that this printer has the capability to utilize the right...

Click HERE for bug reports on Flashforge for Cura.