flashforge creator pro 3d

Accessory to prevent air from entering the Flashforge Creator Pro 3D Printer port

I created this tool caddy to clip on the left or right side of the Flashforge Creator Pro cutouts. Accommodates calipers, scissors, spatulas, box cutter, pens, screw driver and a few other similar accessories. Print Settings Rafts: ...

The filament spools I bought would not fit all the way onto the spool holder that came standard with my flashforge printer which have a 66mm x15mm spacer at their base. Unlike the spools that came with the flashforge which are countersunk to...

I have heard rave reviews for the high quality and low cost of 3D Hero brand of filament on Amazon. So, I decided to check it out because my normal brand was out-of-stock and needed to finish a project asap. When the filament arrived a spool of...

It didn't quite work for the FlashForge Creator Pro / PowerSpec 3D Pro, so I remixed it. This is made to use the spool holder that came with your printer already. To load filament, just put the original spool holder in the spool, and drop it into the...

It didn't quite work for the FlashForge Creator Pro / PowerSpec 3D Pro, so I remixed it. This is made to use the spool holder that came with your printer already. To load filament, just put the original spool holder in the spool, and drop it into the...

These clips allow you to mount and secure a glass build plate cut to fit the standard dimensions of the stock build plate of the Flashforge Creator Pro and it's common clones. Just make 2 (one each for opposite corners and secure using the corner...

The PowerSpec 3D Pro 2 has a door that swings up and the issue is it does not stay up. I have seen other designs with props or keepers that keep it open, but then it got in the way of changing the filament. I designed the door clips to replace...

... the filament guide in place. Break off the little cube supprts under the bucket arms. Insert the bucket with the top end (the model is printed unpside down) into the side holes, and let it naturally flip over. Enjoy. Category: 3D Printer Accessories

My setup doesn't allow for me to use the back mounted filament holders. So I designed some side holders. Because the end of the filament guide tube would move closer and father away, sometimes I had an issue with filament getting off the spool and...

This is a necessary redesign for the FlashForge Creator Pro / Powerspec 3D Pro filament montior designed by Aaron Tunell. These original brackets DO NOT FIT the Powerspec 3d Pro. ...How I Designed This Solidworks 2014

Customized version of http://www.thingiverse.com/thing:941170 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=941170 Instructions Using the following options:...

It is currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D, etc. It helps to see if things are laying down properly, if it's more squished on one side or corner, and to...

They are currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D, etc. It helps to see if things are laying down properly, if it's more squished on one side or corner, and to...

It is currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D, etc. It helps to see if things are laying down properly, if it's more squished on one side or corner, and to...

They are currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D, etc. It helps to see if things are laying down properly, if it's more squished on one side or corner, and to...

This is a filament spool holder for the 2016+ Flashforge Creator Pro, to suit 3D Printz stock. The standard holder is great, but allows the 3dPrintz roll to slide off after a while. This file must be printed in the orientation shown in the...

This set of STL and AMF files provide a sleeve for use with the FlashForge Creator Pro Universal Reel Mount in order to mount Octave large format reels available from http://www.octave.com. This is designed to be used with the FlashForge Creator Pro...

This set of STL and AMF files provide sleeves for use with the FlashForge Creator Pro Universal Reel Mount in order to mount Octave small, large and four (4) color combo format reels available from http://www.octave.com. These are designed to be used...

... vertically. ...They are designed to be used in conjunction with both FlashForge Creator Pro Universal Reel Sleeves and FlashForge Creator Pro Universal Reel Sleeve Stand. ...(See the manufacturer specific reel sleeves also offered by this designer.)

... from http://www.octave.com. ...This is designed to be used with the FlashForge Creator Pro printer available from http://www.flashforge-usa.com.Other sleeve sets can be requested from the designer as needed for your manufacturer's filament reels. ...

This set of STL and AMF files provide a printable design for a rear of printer hanging universal peg board that permits corresponding pegged adapters (available from this designer) and utilities for the FlashForge Creator Pro printer...

It also includes a round recess for placing a 35mm diameter circular magnet in case you want to use the printer mounting bracket for heavier items or in conjunction with other FlashForge Creator Pro printer (http://www.flashforge-usa.com) accessories...

Roo Proto Makerspace Source:https://www.thingiverse.com/thing:654089 PowerSpec 3D Pro/FlashForge Creator Pro Screwless (ABS and Acetone) 40mm Fan Duct by eckerj, published Jan 27, 2015 Props to him for the original design!! ...Print Settings Rafts: ...

This was designed for a PowerSpec 3D Pro printer, but it should also work for many FlashForge printers as well. I believe the 3D Pro is just a rebadged Creator Pro. Also, many other FF printers use the same frame. Print Settings Printer: PowerSpec...

remixed for the 30mm spool tubes on my PowerSpec 3d Pro and added a spool end to match. ... I super glued the spool end into the bushing.

... to keeping the door closed. ... One nice thing about the PowerSpec 3D Pro (and possibly the FFCP) is that the metal frame has built-in nuts for attaching the front fascia with screws. ... Both of these STLs should be printable without support.

The new model (w-03 with firmware v3) can create easily a WIFI link between FlashForge Creator Pro 2016 and your computer with WebDAV protocol. Don't buy the model W-02, it doesn't work. The price was 20€ the 4th January in Amazon.fr, but now at 28€!...

Still a work in progress

I was recently given an old PowerSpec 3D Pro (basically the same as the 2014 FlashForge Creator Pro, aka a Replicator clone) with the circular spool hole in the back. I use (and love) this spool holder on my Replicator 2 but due to the spool hole...