flashforge creator pro glass bed 3d models
252655 3d models found related to flashforge creator pro glass bed.thingiverse
Here are some bed clamps for the glass on the old flashforge creator pro. These are much better than the binder clips because it allows you to print over the entire bed without worrying about crashing into ANYTHING! The fit overtop the existing nuts...
thingiverse
Inspired by this http://www.thingiverse.com/thing:1291106. ...I also designed the support because I was not satisfied by those generated by FlashPrint. Designed for 3mm glass
thingiverse
Flashforge Creator Pro glass bed corner for a 3.5 mm glass this works. I tried every corner file on here and thy did not work for one reason or the other so I made one. ...Increase size 3% if printing in ABS.
thingiverse
Customized version of http://www.thingiverse.com/thing:1949142 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1949142
thingiverse
3mm/5mm Z-Axis Shim for Flashforge Creator Pro Glass Bed
thingiverse
A basic clip for the FFCP 2017 glass bed upgrade. ...(~3mm Glass) Orientate onto side and it clips onto the bed with the flat section contacting the glass. ...(Opposite of preview window)
thingiverse
A revised version of chewbone's Flashforge Creator Pro adjustable Glass Bed Bracket. Changes to corner piece: This now has the screw slot the entire length of the corner so you can remove and swap these in without having to remove the pin completely....
thingiverse
This is a set of four parts designed to hold a 5mm thick glass plate to the heated bed of the flash forge creator pro. The set consists of a RIGHT FRONT, RIGHT REAR, and two pieces for the LEFT side. UPDATED. I found on the Flashforge creator pro...
thingiverse
I'd gotten a 5mm glass bed from my local supplier, so I remixed it to come up with a 5mm version of my own. While I was at it, I also did a 3mm version. Instructions Just pop in it behind the Flashforge logo plate and you're good to go! ... Don't...
thingiverse
... which works well. Print Settings Printer: FlashForge Creator Pro 2016 Rafts: No Supports: Yes Resolution: Creator Pro ABS standard Infill: 35% Notes: A support is only need for the corner piece. ...I set my glass bed to 110c and used some hairspray.
pinshape
A glass platform is perfectly flat, so the original design should work well to hold one in place. However, I was using a flexible platform from PrintInZ (Zebra flex plate). This platform needed to have all four corners clamped down with some degree...
thingiverse
Customized version of http://www.thingiverse.com/thing:570406 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=570406 Instructions Using the following options:...
thingiverse
This shim is made for the glass sold here: http://www.flashforge-eu.com/parts-and-accessories/frosted-glass-build-platform Print Settings Printer: Flashforge creator pro Rafts: No Supports: No Resolution: 300ym Infill: 15%
thingiverse
Customized version of http://www.thingiverse.com/thing:570406 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=570406 Instructions Using the following options:...
pinshape
SummaryThis shim is made for the glass sold here: http://www.flashforge-eu.com/parts-and-accessories/frosted-glass-build-platformPrint SettingsPrinter: Flashforge creator proRafts: NoSupports: NoResolution: 300ymInfill: 15%
cults3d
There are many shims available but I couldn't find any for the 2016 FlashForge Creator Pro which seems to have screws in different places than other models, so here's a remix that fits. Ready-to-use models are available in thicknesses from 2 to 6 mm...
thingiverse
Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 20% Post-Printing It is advisable to make sure the shim is perfectly flat to avoid ‘springiness’ while the Z endstop switch is...
thingiverse
A glass platform is perfectly flat, so the original design should work well to hold one in place. However, I was using a flexible platform from PrintInZ (Zebra flex plate). This platform needed to have all four corners clamped down with some degree...
thingiverse
Customized version of http://www.thingiverse.com/thing:1886458 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of http://www.thingiverse.com/thing:1886458 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of http://www.thingiverse.com/thing:1886458 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of http://www.thingiverse.com/thing:1886458 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1886458
thingiverse
Customized version of https://www.thingiverse.com/thing:1886458 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1886458