flashforge creator pro parts diagram 3d models

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 15-20% Notes: I strongly recommend printing the pieces at .2 resolution to ensure accurate results. My own prints came out perfectly, with no need for...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

A perfect companion for the replacement filament tube holder, this replacement for the Creator Pro 2020 standard spooler was created to remedy two of its flaws: (a) On the standard spooler, the flexible clips used to remove the spool are hard to...

... as they would fit just as well. I've also included a foot with a glue holder, or you can simply print four of the other foot designs. Print Settings: Printer: FlashForge Creator Pro2016 Rafts: No Supports: Yes Infill: 30% Notes: Printed in ABS.

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

Mount for the Paneldue i5, it is made to replace the original LCD display of the Creator Pro 2016 and uses the same screws.

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

Printer Settings: * Printer: FlashForge Creator Pro * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 25 Post-Printing Assembly: Insert the Inside Clamp.stl from within the printer, ensuring it aligns flush with the back of the device. Next,...

This Thing offers both a replica of the top plate of the 2016 FlashForge Creator Pro (unsure whether this is different on older models), and an improved version (‘v2’ suffix). This is the part that connects the umbilical cord and the filament guide...

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

The latest edition of the Flasforge Creator Pro is designed with a proprietary snap-in mechanism, which unfortunately doesn't mesh seamlessly with the spools offered by many other manufacturers.

Here is the spun text: Creator Pro Spool Holder for 1kg ESUN Brand Filaments \n Customized version of http://www.thingiverse.com/thing:1108314 \n Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1108314

Simple Spool Holder for the Creator Pro, I wasn't a fan of most on the site so far. ... Hardware: 1/4-20 Nut 1/4-20x3.5" Hex head bolt Hope you find them useful!

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37...

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37 and...

Summary Mount 1/8" borosilicate glass using http://www.mcmaster.com/#8476k74 to secure it to your Creator Pro. To assemble, follow these steps: I attached this component in 618 nylon with .1mm layers and 50% fill. ...It's likely more than necessary...

Use these components to attach 1/8 inch borosilicate glass from http://www.mcmaster.com/#8476k74 to your Creator Pro machine. ...I fabricated this component using 618 nylon with a layer thickness of 0.1 mm and 50% fill rate, which is probably...

This is to add ABL to Creator Pro, I currently have Marlin flashed to my original motherboard. i had to add mins to mother board for the ABL PWM, also move the fan to the back of the extruder carriage. Not required but my current set up I removed one...

I'm building a hinge for the dome of my Creator Pro, and I had to get creative since I was tired of constantly moving it around. The design requires blocks to support the weight of the dome itself, which presented a challenge. To address this issue,...

These custom-made glass plate bed clips are designed specifically for the 1/4-inch borosilicate glass that FlashForge USA sells online. The clips I created use ABS filament as their material. My main goal was to create an easier alternative to...

I created this to make swapping spools easier without struggling with the holder on the Flashforge.\r\nYou simply need a base plate and print adapters for your spools, which can be left attached to an adapter, allowing you to hang them from the wall...

One of the Creator Pros we inherited had cracked feet, so it could no longer rest on the little rubber pads attached to the base. This foot is meant to prop up the printer using existing screw holes on the printer. ... To print the different sides,...

No Extra Parts Needed Only 3 Parts To Print No Supports Needed Part Cooling Built Into Carriage I printed in PETG 100% infill because all parts are small and thin Parts are oriented in the best print position Also if you edit firmware there a massive...

I needed a compact diameter spool holder for my 3D prints, but every one I looked at was either hard to print or overly complex. ...What I really wanted was a straightforward part that wouldn't need any supports or a raft.

... hotend. ...A filter can be fitted to the enclosure to help eliminate odors caused by various filaments during printing. Designed for use with +/-5mm sheet material (5.5mm gap/opening for sheet material of choice) More parts coming soon...stay tuned!

... with +/-5mm Sheet Material in Mind (5.5mm Gap/Openning for Your Preferred Sheet), This Design Is Perfect for Reducing Noise Output and Keeping Heat Generated by the HBP and Hotend Trapped Inside. More Parts Are on the Way - Stay Tuned for Updates!

This resulted in a print time of about one hour and twenty minutes to an hour and thirty minutes - a significant advantage when printing two parts at once. I created this design after struggling with another spool holder I found online, which...