flashforge creator pro 3d models

... printing at low or medium speeds. Best regards, JPM Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: High Infill: Fully filled Notes: Printed with PLA, without any problems related to melting so far.

... using FlashPrint from FlashForge slicer, with red color PLA filament from DevilDesing. Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.3mm Infill: 15% Notes: Slicer software: FlashPrint from FlashForge

... color PLA filament from DevilDesing. Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.3mm Infill: 15% Notes: Slicer software: FlashPrint from FlashForge Category: 3D Printer Accessories

This is a custom design combining the features of Davefx's Universal Spool Holder for Flashforge Creator Pro (2015) and ajwammock's updated spool offset. Specifically, it is tailored for the older "threaded" version with a round hole of Flash Forge...

Print Settings: Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Notes: Print all parts except the adapter upside down. Designing This Project I designed this from scratch using...

A premium tool caddy specifically designed for FlashForge Creator Pro models released after 2016 comes with a robust all-in-one molded side panel.\r\n\r\nMost tool caddies I've tried lack sufficient support, causing them to shift, flex, or break...

... Best regards, fdk Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 Infill: 20% Notes: This was printed with ABS Bed temp: 95 Extruder: 238 A bit of cleanup inside the magnet holes and it snaps together smoothly.

This filament tube holder is an add-on to the FlashForge Creator Pro (8cm tube spacing) to prevent the filament from getting tangled around the spool axis. This happens when the filament tube entry point is not aligned with the spool (as is the case...

UPDATE: I upgraded it to version 2: http://www.thingiverse.com/thing:1357645 This streamlined and highly functional holder for a 40mm nozzle fan fits seamlessly into the two small holes on top of the extruder carriage of my Flashforge Creator Pro.

Use this to test the bed leveling of your Flashforge Creator Pro and ensure that your bed is perfectly flat. This tool is especially useful for detecting bubbles after installing a PEI or BuildTak surface. ... Features: * Magnetic for easy alignment *...

In typical Chinese fashion, FlashForge Creator Pro 2016 models seem to be shipped with small variations, for instance some are shipped with little round feet instead of the elongated feet on my model. User Shftatsix notified me of the update to...

I have taken a Shaxon Spool Holder design intended for the Replicator 2 and adapted it to be compatible with the Flashforge Creator Pro. This custom-made spool holder is suitable for use with filaments that come on smaller reels, much like the ones...

In typical Chinese fashion, FlashForge Creator Pro 2016 models are often shipped with minor variations, such as some featuring small round feet instead of elongated feet like my model. User Shftatsix brought to my attention the update made to...

###UPDATE: I made a better one: http://www.thingiverse.com/thing:1272643 This is a really simple and functional holder for a 40mm nozzle fan for the Flashforge Creator Pro. It simply snaps into the two small holes on top of the extruder carriage....

Print Settings Printer: FlashForge Creator Pro 2016 Rafts: No rafts are required for this design. Supports: Yes, supports are necessary to ensure a successful print. Resolution: A resolution of 0.2mm is recommended for optimal results. ... Notes Both...

I needed a more reliable solution for attaching back mounted spool holders on my Flashforge Creator Pro 2016. After conducting a thorough search, I couldn't find any suitable options that met my requirements. So, I decided to take matters into my...

A simple clip which can be fitted using any of the casing screws (I have used the top rear screw of each side panel) allowing you to easily clip the left or right filament tube out of the way when you haven't got anything loaded into it. Print...

Printing settings used for this project include: - Layer height: 0.2mm (first layer thickness set at 0.3mm) - Solid layers on top and bottom: both set at 4 - Infill percentage: 30% - No skirt or brim was applied Available files for download are: -...

You can also buy similar threaded inserts from ebay but you will need to dremel one end to be conic as shown in the picture. Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: Material:...

That's a direct quote from the FlashForge Creator Pro 2016 manual, but I've found that this printer can handle printing PLA through the right extruder for excellent dual-strusion prints. All it needs is an upgraded fan duct. Take a look at the...

Print Settings: Printer: FlashForge Creator Pro 2016 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 15% Notes: While printing without supports is feasible, I strongly recommend utilizing them. If you have Simplify3D, navigate to the Customize...

Relocates the spools from the back to the sides on the FlashForge Creator Pro 2. Uses the original PTFE tubes. Also compatible with the Creator Pro 1.3D Printed ComponentsRod Holder (Print 2)Filament Holder (Print 2)Tube Holder (Print 2)Tube Clip...

... works well. Print Settings: Printer: FlashForge Creator Pro 2016 Rafts: No Supports: Yes Resolution: Creator Pro ABS standard Infill: 35% Notes: A support is only needed for the corner piece. ...I set my glass bed to 110c and used some hairspray.

Print Settings Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: .20mm Infill: 20% Notes: Sliced with Simplify3D Filament - ABS or PLA (ABS preferable for high temperature applications) Infill - 25% Solid layers - 3 top,...

You can purchase the plate at: http://www.homedepot.com/p/AFINIA-Borosilicate-Glass-Printing-Surface-for-H800-AFINIA-H800-BORO-GLS/206653633 Print Settings Printer: Flashforge Creator Pro Rafts: Yes Supports: Yes Resolution: .200 Infill: 100% Notes:...

... the Pi and set up in the yaml.conf to low too. Basic code for this can be found in the comments. Printer Settings: Flashforge Creator Pro Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 55% Notes: An infill of ~30% should work fine too.

I successfully printed this design on my FlashForge Creator Pro 2016 without issues. To help others print without supports, I've added images showing the support guides and cuts where the model's nerve is observed. This can be a useful reference...

A Reimagined Version of Chewbone's Flashforge Creator Pro Adjustable Glass Bed Bracket Enhancements to Corner Piece: The screw slot is now extended along the entire length of the corner, allowing for effortless removal and swapping of these...

Use this to test bed leveling of your Flashforge Creator Pro and verify flatness of the bed to detect bubbles after installing a PEI or BuildTak surface. Features: * Magnetic * Adjustable, easy to customize dimensions for precise printer tolerances....

A week ago, I got my FlashForge Creator Pro 2016 and was blown away by its performance. However, some issues needed addressing. Firstly, it's really hard to fit filament spools from other brands in the included spool holders, but printing...