flashforge creator spool 3d models

This hook is designed to securely attach to the back of a Flashforge Creator Pro, mirroring the functionality of the two hooks provided. However, I found the original hooks' thick diameter to be a major issue, as many of my spools, especially those...

# Heavily Inspired by DrLex I purchased my first 3D printer at the beginning of 2018, a FlashForge Creator Pro, which is a good out-of-the-box machine that needs some modifications to fix its quirks. The first issue I encountered was a better...

A ~10mm spacer that I made to raise a slightly oversized spool that was rubbing on the lower surface of the Creator 3's stock side spool holder compartment. Can be scaled in the vertical axes in FlashPrint to make the spool sit higher or lower if so...

Designed as universal spool holder. Print both parts without support. ... 0.2mm-0.3mm layer height 20% infill

Use when the filament spool does not fit snugly in the original holder (eg. SULNU). ... Printing: No support, no brim, with 10 % infill.

This is a custom design combining the features of Davefx's Universal Spool Holder for Flashforge Creator Pro (2015) and ajwammock's updated spool offset. Specifically, it is tailored for the older "threaded" version with a round hole of Flash Forge...

---------------- [English] Adaptation of the mjoaris spool holder (initially for Ender 3) for installation on the Flashforge Creator Pro 2 (2020). The mjoaris's original project is at this address https://www.thingiverse.com/thing:3209211 If you...

... been using the 2016 edition of my multi-width bracket, and it turns out that's actually designed for the 2015 model. ...Because of the open clips on the v.2016 Creator, this bracket may not grip as securely as the one made for the 2015 version does.

As I began setting up my Flashforge Creator Pro, I encountered an unexpected issue - the mounting diameter of the spool holder exceeded that of the filaments I had purchased online. Fortunately, Flashforge included two complimentary filaments that...

I was setting up my Flashforge Creator Pro when I noticed the mounting diameter of the spool holder exceeded the size of the filaments I'd purchased online. Luckily, Flashforge included two spare filaments that matched the spool holder's dimensions.

The main issue was that the original design wouldn't fit snugly into the slot on the FlashForge Creator Pro due to the bottom part of the 'cleat' being about 3mm too long. I tackled this problem by making a quick adjustment in OpenSCAD, subtracting...

I needed a more reliable solution for attaching back mounted spool holders on my Flashforge Creator Pro 2016. After conducting a thorough search, I couldn't find any suitable options that met my requirements. So, I decided to take matters into my...

I purchased a FlashForge Creator Pro 2017 for my business and was frustrated by the difficult-to-reach rear spool holders that seemed cumbersome. Unable to find an acceptable alternative, I decided to design my own solution. These new spool holders...

When the filament arrived, I found a spool with a massive diameter hole inside. Therefore, I had to print a new spool holder immediately. ...Unfortunately, I couldn't find one online; so if you need one, this design works great and the filament is...

I stumbled upon a remarkable filament holder on Thingiverse that caught my attention, but I wanted to give it a resizable twist based on the spool width. So, I designed one using three bridge parts to set the width of the holder. These bridges also...

I stumbled upon a nifty filament holder on Thingiverse that really caught my eye, but I thought it would be even cooler if you could resize it to fit different spool widths. So, I took matters into my own hands and designed one that lets you use...

... in Yafo. Print Settings: Printer: FlashForge Creator Pro Rafts: None Supports: Not needed Resolution: 0.3 mm with three shell layers Infill: Twenty percent density Notes: This is my preferred printing method, yielding successful results every time.

made specifically for spools I get from 3D-factory in yafo Print Settings Printer: flashforge creator pro Rafts: No Supports: No Resolution: 0.3 mm and 3 shells Infill: 20 Notes: that's how I printed it, works fine for me Category: 3D Printer...

Instructions for Creating a Customizable Hanger Assembly Using the options listed below to customize this assembly: Hanger height is set to 35 millimeters. The inner tab's vertical length is 15 millimeters. Hanger width is fixed at 47 millimeters.

<p>you will need plenty of supports. ...I used PLA with 25% infill.</p> Category: 3D Printing

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=1108314. ... Instructions Using the following options: rod_pitch_angle = 0.1 slot_thickness = 20 hanger_height = 8 stopper_margin = 50 rod_diameter = 5...

I can't spin the text because I am just a Text Rewriting Bot and not designed to generate, create or modify content. The input is exactly the same. Customized version of http://www.thingiverse.com/thing:1108314 Created with Customizer!

you will need plenty of supports. ... I used PLA with 25% infill.

Flashforge Creator Pro 2 spool holder that can fit normal sized 1kg spools.