flashforge dreamer 3d models

Here is the rewritten text. Human: Close-off nozzles for Extruder Blowers, choose from either 5.5mm or 6mm diameter. ... Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 mm Infill:...

Humans Design a Spool Specifically to Work with FFCPro Filament Feeders, Compatible with IDs Up to 52mm in Diameter. Offered in Both Left and Right Orientation Models, Guaranteeing 100% Infill Capacity. For Safety's Sake, While Still Maintaining...

I designed custom spool spacers to enhance stability and utilized the existing spool holders from my printer. I aimed for more workspace on my desk by streamlining the setup. This revised feed system now directs filament directly into the printer...

I created the Ultimate Rotating Spool Holder for my Makerbot Rep 1 and was impressed by its performance, so I adapted the design to work seamlessly with my CTC printer as well. To do this, I redesigned the base of the holder, and the results are...

Keep remote control out of children's reach and educate them on proper usage to prevent objects from getting stuck in ventilation system fans.

For Mini USB Cable (0.5mm)

I'm creating a custom fan duct based on the dual fan duct design by DrLex. ...This single-extruder version targets the right extruder only, making it perfect for situations where repairing the left side is impractical due to issues like PTFE tube...

I designed a spool holder that's incredibly easy to print, requiring no supports and minimal infill if you use enough shells. For my own prints, I used three shells with a 0.2mm layer height, printing at 60mm/s for the inner layers and slowing down...

Summary Mount 1/8" borosilicate glass using http://www.mcmaster.com/#8476k74 to secure it to your Creator Pro. To assemble, follow these steps: I attached this component in 618 nylon with .1mm layers and 50% fill. ...It's likely more than...

I adored the caddy, however, I required a storage solution to keep my new holiday gift - a set of pliers - within easy reach.

I had a problem with layer shifts due to the nozzle bumping into object and shifting whole table slightly. This is a solution. You just put it like in the picture and forget about it. ...Does not interfere when sliding the top plate.

This component closely resembles its predecessor, a standard motor design. ...To get it up and running, carefully thread the M3 screw holes with a precision tap.

Remove the tube from the printer immediately. Drill a hole of 9mm or 0.375" in the center of the original door and modify it so that the tube has an unobstructed path. To achieve optimal results, create the M5x0.8 thread after printing is...

Humans construct foundational elements that enable creation of various supports and accessories.

Something I came up with to run external rolls of filament on my 3D Printer. Two parts: 1) A clip for the back, clips onto the original filament holder, which guides the filament through. 2) An adapter for the head that holds onto the original...

Hi Guys, I'm using a PowerSpec ultra with Dual Flexion Extruders, where I heated up the fan shroud and flexed it to drop the ends down a few more mm for better alignment to the nozzles with this new setup. This might not be an issue for anyone else,...

To get a more centered filament path, add an extra guide bracket at the back of the printer that moves the filament away from it and towards the spool. When using the top cover for ABS printing, one of these brackets works best. Carefully insert the...

We Must Shrink Hole Openings to an Absolute Minimum

I redesigned the attachment system to accommodate a Logitech C270 webcam using the standard screw mount, securing it with an M3x20mm screw. When printing this piece, I strongly advise adding supports due to its complex design. A slight misalignment...

The Finder's leveling system performs adequately without adjustments, yet precision calibration is required to achieve perfect leveling. Upon searching, a versatile bed level test design was discovered at https://www.thingiverse.com/thing:97151,...

Reimagined Stepping Block: Filling the Void Left by Your Missing Left Stepper This custom insert seamlessly occupies the space where your left stepping component was removed.

I picked up some spool holders on my second-hand CNC machine and these are exactly how they looked when I got them. ...They function perfectly and possess a sturdy build.

I needed a compact diameter spool holder for my 3D prints, but every one I looked at was either hard to print or overly complex. ...What I really wanted was a straightforward part that wouldn't need any supports or a raft.

This is an adaptation of "Filament Holder" by Functional Design. Designed to hold a 1KG Spool using the allen key that comes with the Adventurer 3 as the shaft and adding a filament guide because my filament kept unwinding. ... Prints well with the...

I'm building on an existing remix, giving full credit to its originator - I've simply added some stabilizing features like holds and pegs for improved structural integrity and alignment.

Simple accessory allows external PLA filaments to feed through the side. Functionality improves significantly when the drum is positioned very close to the printer and spins smoothly without any wobble. The drum shown in the image has an additional...

The latest edition of the Flasforge Creator Pro is designed with a proprietary snap-in mechanism, which unfortunately doesn't mesh seamlessly with the spools offered by many other manufacturers.

I'm going to try that. ...I've got my 3D modeling program up and running on TinkerCAD, ready to upload designs to our ReplicatorG printer at home.

The Cooling System Module