flashforge files 3d models

This is a camera holder designed specifically for the ELP style camera found at tinyurl.com/ztsb7sz, perfect for use with the FlashForge Creator Pro. Version 1 of this project is engineered to secure the camera in the corner, ideal for printing PLA...

... require more complex printing, necessitating supports, etc. I did use a raft because the base is very thin, but trimming the end would likely allow printing without it. Printer settings: Printer: Flashforge Creator Pro Rafts: Yes Supports: No

I was struggling to figure out a way to attach my Pi to the FlashForge Creator Pro without compromising its casing with unsightly holes. Since I needed to add filament support anyway, I cleverly integrated both issues into one seamless solution.

... something special for itself? Print Settings Printer: FlashForge Creator Pro Rafts: Yes Supports: Yes Resolution: 0.1mm Infill: 100% Notes: These are the settings I used but hey, feel free to experiment. ...I prepped the gcode with Simplify 3D.

This essential Lid Spacer is designed specifically for use with Flashforge Dreamer and Dremel Idea printers when pairing them with my OmniStand Mod Backside or Sidepanel, which includes a Filamentguide feature. ... If you're fed up with tangled filament...

Human: Custom FlashForge Creator Mod of Replicator Cooler Optimized for Enhanced Performance My key modifications centered on enhancing structural integrity, tailored compatibility with FlashForge hardware, and adjustable air velocity to optimize...

Print Settings Printer: Flashforge Creator Pro Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 50% Notes: Please consult the attached settings for further reference. How I Designed This Extruder settings were carefully adjusted. Infill...

Summary Mount for Flashforge Creator Pro (and probably all MakerBot clones) Smart camera available on AliExpress: http://www.aliexpress.com/item/Sricam-SP009-Wireless-IP-Camera-WiFi-HD-720P-indoor-1-0MP-P2P-720P-Video-IR-Network/32603411551.html...

**Print Settings:** **Printer:** FlashForge Creator Pro **Rafts:** No **Supports:** Yes **Resolution:** 0.1mm **Infill:** 20% **Notes:** Results may vary, but with the right conditions, this design will shine! ...Go with the flow and you'll be...

The Flashforge Creator Pro has a notorious problem with yanking filament off the spool and tangling it around the spool holder, causing frequent jams. This Thing fixes that issue by pulling filament from the center of the spool instead of the side,...

This is a revamped version of Seamongrel's FlashForge Creator Pro 2016 Lid Holder, tailored to utilize one single 3/4" ceramic disc magnet. I opted for an "ook" brand magnet from Walmart, which measures approximately 18mm in diameter by 5mm thick.

... (OD) and 2mm (ID) to smooth out filament flow. ...You may need to enlarge the holes a bit; I left them tight to hold the Teflon tubes in place.\nPrint Settings:\nPrinter: FlashForge Dreamer\nRafts: No\nSupports: No\nResolution: 100 microns\nInfill: 40%

This simple filament spool hanger was designed to fit on a Flashforge Creator Pro (or Flashforge Creator Pro 2). They fit in the slots on the back where the stock hangers go. The stock hangers were not long enough or small enough diameter for some...

This cover will give your Flashforge a polished look by concealing the green Z-axis end stop switch and allowing it to blend in seamlessly with its surroundings. Please visit the outstanding filament guide: https://pinshape.com/items/326... To stay...

Here is the rewritten text in American English: "I created this design for my FlashForge Dreamer so I can attach one to each side of my printing cart. After searching on here, I found some designs that were too large to fit on the Dreamer bed, so I...

Got tired of fumbling with my caliper and trying to get a straight cut when i replaced the PTFE tube on my Flashforge Finder. so i looked. and while there's many tube cutting jigs, and even adjustable ones, i wanted one i could just keep with my...

To enhance precision on a FlashForge Replicator, remove an extruder to decrease weight on the Gantry. This reduces backlash, as it accounts for over 25% of y-axis weight and 40% less weight on X-axis stepper movements. Install a block to tighten...

This replacement spool holder is designed specifically for the FlashForge Creator Pro, providing a precise fit for every spool I've encountered, including Hatchbox brand. Its mounting slots align perfectly with those found at the back of this...

I got tired of threading the needle to get my filament loaded on my FlashForge Creator Pro and my previous filament tube holder wasn't sticking out far enough after I started using my low friction spool holders, so I created this thing to make...

Use these brackets to attach rubber isolation pads securely to the Flashforge Creator Pro. The brackets replace standard covers that usually sit on printer bases. ...Replace rubber feet pads with JW Winco GN 451 Cylindrical Vibration Isolation Mounts...

The clip could be held securely by pushing it onto the inside rib of the FlashForge Dreamer body, but I decided that since the X-axis motor wires move constantly, a more secure attachment was needed. I chose to tap the clip with an M3-0.5 thread and...

This adapter secures the cooling fans and heatsink on the FlashForge Creator X, positioning them at the rear of the extruder rather than the front. This design grants improved access to observe filament flow into the nozzles while maintaining...

... a small end stop within the tube's nozzle. Print Settings: Printer: Flashforge Creator Pro Rafts: No rafts will be printed Supports: Print supports are enabled Resolution: 0.3mm resolution is selected Infill: 20-25% infill density is chosen

To enable Flashforge Dreamer to support standard 1kg spools, follow these steps: - Remove the bottom plate. - Release the original M3 hex nuts. Note that you may need two longer nuts, such as M3 x 30, to complete this process. - Increase the height...

We must minimize the acrylic hat's rattling noise and optimize air flow.\nOptional - A sturdy 8x5mm magnet to firmly secure the holder in place\nPrint Settings\nPrinter:\n The Flashforge Creator Pro was used for this project\nRafts:\n Raft support is...

This tool is designed to provide an optimal vantage point for capturing stunning timelapses using the FlashForge Finder 3D printer and the Xiaomi Mijia 4K sports camera. Its compact design allows it to fit seamlessly within the confines of the...

This spool holder is made to go on the outside of a Flashforge Adventurer 3. This allows you to use third party spools of filament. Print the spool holder parts. Determine where you want to mount the spool holder on the filament door. Mark the top...

Designed specifically for the Flashforge Creator Pro, this sturdy backplate ensures smooth and effortless printing with its precision-engineered fit. The durable construction withstands even the most demanding print jobs, providing reliable support...

I recently acquired a Flashforge Creator Pro. The included spool holders feature an oversized diameter that failed to accommodate any of the filament spools from my previous printer. To overcome this issue, I designed and created a custom spool...

This holder allows you to attach your Palette 2 to the side of your FlashForge Finder. With these holders, you can use the short (50cm) tube that comes with the Palette 2. CRUCIAL: Only mount on the LEFT side of the Finder. If mounted on the right...